Chain Soldering Cost: What You'll Pay in 2026

Chain soldering costs $30 to $95 for most broken chains in 2026. Through our mail-in service, a single break on a sterling silver chain starts at $30, with the final price determined by the metal, the chain's weave, how many breaks there are, and whether the chain is hollow — all shown online before you ship.

Walk-in jewelers typically charge $25–$75 per solder joint, though many have a shop minimum of $40–$50 regardless of the job. Here's exactly what moves the number, so you can tell a fair quote from a padded one.

What chain soldering costs by metal

Chain metal One break (from) Two breaks (from)
Sterling silver $30 $47
10K yellow gold $37 $54
14K yellow gold $41 $58
18K yellow gold $49 $66
14K white gold $48 $65
18K white gold $56 $73
Platinum $133 $150

These are prices for simple weaves — ball, cable, and box chains. Complex weaves add to them, as covered below.

What drives the price up or down

Number of breaks

Each break is its own solder joint: cutting away the damaged links, closing the gap, soldering, and blending the joint. In our pricing the second break adds $17, a third adds $35 total, a fourth adds $52. If your chain snapped in one place, you pay for one joint — a shop that quotes "per repair session" without counting joints is rounding up at your expense.

The weave

  • Ball, cable, box: no surcharge. Open links are the easiest to isolate and rejoin invisibly.
  • Snake: adds $13. The tight segmented sleeve has to be rebuilt so the repair flexes like the rest of the chain.
  • Rope: adds $25. The twisted strands must be re-woven before soldering or the joint shows as a flat spot.
  • Cuban: adds $38. Interlocking flattened links mean the joint is soldered, then re-filed and re-polished to match the faceted profile.
  • Tennis bracelet: adds $64 — every link carries a stone, so the repair happens millimeters from settings that can't take stray heat.

Hollow vs. solid chains

This is the distinction most people don't know until a jeweler mentions it. A hollow chain is made from tubes of gold rather than solid wire — it looks substantial but weighs half as much. Soldering hollow links is delicate work: too much heat and the thin wall collapses or burns through, which is why hollow construction adds $20 in our pricing and why some walk-in shops refuse hollow chains entirely.

Quick test: check the weight. A 20-inch, 4mm solid gold chain has real heft; the same chain in hollow construction feels closer to costume jewelry. The clasp tag sometimes reads "hollow" or the receipt will say it. If you're not sure, select "not sure" when you order — we confirm on the bench and your price doesn't change without your approval.

When a chain isn't worth repairing

An honest answer some shops won't give: sometimes the repair costs more than the chain justifies.

  • Thin gold-plated fashion chains. Solder heat burns off plating around the joint, so the repair works but leaves a visible patch. If the chain cost $40 new, a $30+ repair that mars the finish rarely makes sense.
  • Hollow chains that have broken more than once. Repeated breaks usually mean the walls have worn thin along the whole length. Each solder holds, but the next break is already coming.
  • Very fine chains (under 1mm) with multiple breaks. At three or four joints you may be approaching the price of a comparable new chain — worth checking before you commit.

If a chain has sentimental value, none of this math applies — a chain that belonged to your grandmother is worth soldering at any reasonable price, and hollow or plated construction just means the work needs a careful bench. We'll tell you which case yours is when we photograph it on arrival.

What the bench actually does

A proper chain solder is not a dab of glue-like solder on the break:

  • Assess under magnification: find the break, and check the neighboring links — the ones next to a break are usually stretched too.
  • Remove damaged links: a stretched link left in place is next month's break.
  • Solder with matched alloy: the joint is soldered with metal matched to the chain's karat and color, so it doesn't show as a dull or yellowed spot.
  • Blend and test: the joint is filed, blended into the weave, and pull-tested.
  • Polish the whole chain: the full chain is cleaned and polished, not just the repair site.

Chain repair vs. the related fixes

"My chain broke" covers several different repairs, and they're priced very differently — worth knowing before you order:

What actually happened The right repair Price (from)
A link snapped mid-chain Chain soldering $30
The clasp won't close or spring back Clasp replacement $48
The pendant fell off but the chain is fine Jump ring repair $19
The pendant's own loop (bail) broke Bail repair $39
Chain is intact but hopelessly knotted Chain untangling $15

The jump ring case is the one people most often misdiagnose: the small round connector between pendant and chain pulls open under stress — by design, actually, since it's the sacrificial link that saves the chain. Soldering it closed is a $19 job, not a $30+ chain repair.

Making the repair last

Most chain breaks aren't freak accidents; they're habits. A soldered joint done well will outlast the rest of the chain, but the rest of the chain has the same life it had before, so:

  • Don't sleep in chains. Overnight tension against a pillow is the leading cause of stretched links and morning breaks.
  • Take necklaces off before pulling shirts over your head — the snag-and-jerk is how most clasps and jump rings fail.
  • Watch pendant weight. A heavy pendant on a fine chain concentrates wear at two links; if your chain keeps failing at the pendant, the fix is a heavier chain or a lighter pendant, not a third solder.
  • Get the whole chain looked at when one link goes. Our repair includes checking the neighboring links and the clasp — the two places the next break is most likely hiding.

Red flags with cheap chain repair

  • A visible lump or discolored spot at the joint — mismatched solder or an unfiled joint.
  • The chain kinks at the repair. A good joint flexes like every other link; a stiff spot means excess solder wicked into neighboring links.
  • No willingness to quote the clasp. Chains often break at the clasp because the clasp is worn out. If the spring is gone, soldering the chain fixes the wrong problem — a clasp replacement (from $48) is the durable repair.
  • "We'll see when we open it up." The metal, weave, break count, and hollow/solid question are all knowable up front. A shop that won't price from those facts is leaving room to pad.

How mail-in chain repair works

You select your chain's metal, weave, and number of breaks online and see the full price at checkout. Round-trip shipping is $30, with $100 of coverage included and full-value coverage available at 2.5%, and your chain is photographed on arrival and again before it ships back. Every solder joint carries a 1-year workmanship guarantee — if a joint we made fails in normal wear, we redo it. Rush service is a flat $50 if you need it back fast.

Nervous about putting a gold chain in the mail? That's reasonable, and it's exactly what our prepaid, insured UPS label and packing guide are designed for — our guide on whether it's safe to mail jewelry walks through how tracking, insurance, and discreet packaging work together.

Chain soldering — from $30 →

Clasp replacement — from $48 →

Jump ring repair — from $19 →

Common questions

How much does it cost to solder a broken chain?

Most chains cost $30 to $95 to solder in 2026. A single break on a sterling silver cable chain starts at $30; 14K yellow gold is $41 and 18K white gold is $58. Complex weaves add more — rope chains add $25 and Cuban links add $38 — because the joint has to be rebuilt to match the weave.

How much does each extra break cost to repair?

In our pricing a second break adds $17, a third adds $35 total, and a fourth adds $52. Each break is its own solder joint: damaged links are removed, the gap is closed, and the joint is soldered and blended. You should only ever pay per joint, not a vague per-visit rate.

Can a hollow gold chain be soldered?

Usually yes, but it's delicate work — hollow links are thin gold tubes that collapse or burn through under too much heat, which is why hollow construction adds $20 and why some walk-in shops refuse the job. A hollow chain that has broken repeatedly is often worn thin along its whole length and may not be worth repairing.

Is it worth repairing a cheap or gold-plated chain?

Often not. Solder heat burns the plating around the joint, so the repair holds but leaves a visible patch — on a $40 fashion chain, a $30+ repair rarely makes sense. The exception is sentimental value, where careful bench work is justified at any reasonable price.

Why does my chain keep breaking at the clasp?

Usually because the clasp itself is worn out — the spring weakens and the chain takes stress it shouldn't. Soldering the chain fixes the symptom; replacing the clasp (from $48) fixes the cause. A good bench will look at both and tell you which you actually need.

How long does a soldered chain repair last?

A properly soldered joint with matched alloy is as strong as the original links and should last the life of the chain — ours carries a 1-year workmanship guarantee. If a repair kinks, stiffens, or shows a discolored lump, it was done with excess or mismatched solder.