Prong repair costs $29 to $154 for most rings in 2026. Through our mail-in service, re-tipping 1–4 prongs starts at $29, with the price rising with the number of prongs and the metal — you see the exact figure online before you ship.
Walk-in jewelers typically charge $25–$60 per prong or $100+ for a full set, and the quotes vary wildly because "prong repair" covers three different jobs. This guide separates them — re-tipping, rebuilding, and full re-pronging — and shows what each actually costs, because the difference between a $29 repair now and a lost diamond later is the whole point.
Prong repair cost at a glance
| Number of prongs | Sterling silver | 14K yellow gold | 14K white gold | Platinum |
|---|---|---|---|---|
| 1–4 prongs | $29 | $53 | $57 | $224 |
| 5–9 prongs | $74 | $98 | $102 | $269 |
| 10–15 prongs | $99 | $123 | $127 | $294 |
| 16+ prongs | $154 | $178 | $182 | $349 |
Pricing is per job, not per prong — a tiered structure that reflects how the work actually scales on the bench. Re-tipping four prongs is one setup, one alloy, one polish; sixteen prongs across a halo is hours of work under the microscope.
Re-tip, rebuild, or re-prong: which one do you need?
Re-tipping — from $29
The tip is the small cap of metal folded over the stone's edge, and it's the part that wears. Years of contact grind it down until the prong looks flat-topped or the stone starts to rotate. Re-tipping adds fresh metal to the existing prong and reshapes it over the stone. It's the right job when the prong's body is still sound — the most common case, and the cheapest.
Rebuilding — from $29
When a prong has snapped off, caught on a sweater and bent flat, or worn past the point of re-tipping, it's rebuilt from new metal — a new prong shaped, soldered to the setting, and matched to its neighbors in height and profile. Priced on the same tiers as re-tipping; the difference is what the bench does, not what you pay.
Full re-pronging — the 16+ tier
When most or all prongs on a setting are worn — common on rings worn daily for 15–20 years — patching them one at a time stops making sense. Rebuilding the full set (the 16+ prong tier, from $154) restores every contact point at once, and on a heavily worn head it's often the honest recommendation over paying for four prongs this year and four more next year. If the head itself is worn through, replacing the head is the next step up; we'll tell you from the arrival photos if that's what we're looking at.
What drives the price
- Prong count: the tiers above. A solitaire has 4–6 prongs; a three-stone ring 12–18; a halo can pass 20.
- The metal: new tips must match the ring's alloy. 14K yellow gold adds $24 over silver, 18K white gold adds $36, and platinum adds $195 — platinum prong work needs its own solder, its own tools, and much higher heat.
- What's next to the prong: heat-sensitive stones (emerald, opal, pearl) require slower, laser-assisted or heat-sinked work. This is bench craft, not an upcharge line in our pricing, but it's why some shops refuse the job.
The math that matters: $29 now vs. a lost stone later
Prongs fail quietly. A worn tip doesn't drop the stone the day it wears through — it holds on for months while the stone loosens, then lets go on a car door or a towel. What replacement costs depends entirely on the stone: a small melee diamond might be sourced and set for well under $200, while replacing a half-carat center stone runs into four figures at market prices — and if the ring was never appraised, insurance may cover only a fraction of it.
Against that, prevention is cheap and knowable: re-tipping worn prongs starts at $29, and a stone tightening service — every stone checked under magnification and secured, with a written report — is $50. If you can catch a prong on a cotton ball dragged over the setting, or see a stone move when you press it gently with a toothpick, the cheap window is still open.
Stone tightening — $50 with written report →
Already lost the stone? Our stone replacement cost guide covers sourcing and setting a match.
What the bench actually does
- Inspect every prong under magnification — not just the one you noticed. Wear is symmetrical; if one tip is gone, its opposite number is close behind.
- Protect the stone. Diamonds tolerate direct heat; most colored stones don't. The stone is shielded, heat-sinked, or in some cases unset first.
- Add matched metal. Tips are built with alloy matched to karat and color, then shaped so the repaired prong is indistinguishable from its neighbors.
- Seat and pressure-test the stone, confirming it can't rotate or rock.
- Finish: polish the setting, and re-plate white gold with rhodium so the repair disappears.
How to check your own prongs in two minutes
You don't need a loupe to catch most prong problems early. Once every few months, in good light:
- The cotton test. Drag a cotton ball or the corner of a tissue slowly across the setting. Anywhere it snags, a tip is worn, lifted, or cracked.
- The wiggle test. Press the stone gently with a wooden toothpick from a few angles. Any visible movement or faint clicking means the stone is loose — stop wearing the ring until it's checked.
- The profile check. Look at the prongs from the side. Healthy tips are small rounded domes curling over the stone's edge; worn ones look flat-topped, and failing ones look like posts standing next to the stone rather than over it.
- Listen after knocks. If the ring took a hard hit on a door frame or car door, check it that day. Bent prongs rarely announce themselves.
Rings worn daily deserve a professional check under magnification about once a year — that cadence is the difference between finding a $29 problem and a missing stone.
How long the work takes
Re-tipping a few prongs is a same-day bench job; a full re-prong or work around heat-sensitive stones can take a couple of days. For mail-in, your promised-by date — bench time plus shipping both ways — is shown before you check out, and rush service is a flat $50 if a proposal or anniversary is bearing down on you.
Red flags with cheap prong work
- Gray or yellow-tinged tips on a white setting — low-karat solder blobbed on instead of matched alloy.
- Repairing only the prong you pointed at. If nobody inspects the other prongs, you'll be back in six months.
- No stone security check afterward. The entire purpose of the prong is the stone; a repair that ends without pressure-testing it is unfinished.
- Fear of your stone. If a shop shrugs at "is my emerald safe with heat?", walk. Handing over a ring should come with a plain answer about how the stone will be protected — and if you're worried about a mail-in service having your diamond at all, we wrote honestly about whether a jeweler would swap your diamond and how photo documentation makes it verifiable.
How mail-in prong repair works
You count your prongs (a photo with your order helps if you're unsure), pick your metal, and see the full price at checkout. Round-trip shipping is $30, with $100 of coverage included and full-value coverage available at 2.5%. Your ring is photographed on arrival and again after finishing — you can literally compare your stone before and after. Every repair carries a 1-year workmanship guarantee, and rush service is a flat $50.