Jewelry repair questions · Pearls
A pearl came off my ring or earring. Can it be reattached or replaced?
From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )
The short version
- Pearl and peg intact: usually a straightforward reset. The old adhesive is cleaned out and the pearl is cemented back on with jeweler's epoxy, with no heat anywhere near it.
- Peg bent or snapped: the metal has to be repaired first, with the pearl off, because heat damages pearls.
- Pearl lost: a replacement has to match in size, shape, color, luster and surface, and for earrings it has to match its partner. That's a sourcing job, quoted only once a jeweler has seen the piece, and a match can't be promised.
- Don't reach for household glue, and don't wear the piece. Put the pearl and the jewelry in a small sealed bag.
- At JewelryRepair.com: a free photo quote through the contact page or the on-site chat, or the $19 Mail-In Evaluation, credited in full.
Prices
| Service | Price | What's included |
|---|---|---|
| Mail-In Evaluation | $19 | For a pearl that came off a ring or earring: the whole piece examined under magnification, pearl and peg included, with photos and an itemized quote. Credited in full toward approved work; a declined piece ships back with the photos and findings. |
| Custom Work & Modifications | $10 | If the pearl is lost and you'd rather redesign the piece, or a lost earring has to be matched: a jeweler reviews your photos and quotes the work before anything proceeds. Existing stones or gold can be reused or credited. |
How a pearl is held on a ring or earring
Most gemstones are gripped by metal: prongs, a bezel or a channel. Pearls usually aren't. On rings, stud earrings and many pendants, the pearl is half-drilled, meaning the hole goes only partway in, and it sits on a small metal peg rising from a cup or pad. The joint is adhesive. In a Ganoksin Orchid forum exchange on gluing pearls, a pearl dealer's answer for a half-drilled pearl going onto a post was jeweler's epoxy from a jewelry supply house, and in a separate Orchid thread on pearl setting, a bench jeweler advises twisting the post for strength and a tight fit.
That design keeps metal off the face of the pearl, but it means the bond can let go without anything visibly breaking:
- Chemicals reach the joint. GIA says pearl can be damaged by many chemicals and all acids, and names hair spray, perfume, cosmetics and even perspiration. A ring pearl also meets soap and hand lotion every time you wash your hands.
- Cleaning machines and heat. GIA says pearls should never be cleaned in an ultrasonic or steam cleaner, and that high heat can burn cultured pearls or cause discoloration, splitting or cracking.
- Knocks and twisting. A pearl on a ring takes blows a stud never does, and twisting a pearl to check whether it's loose strains the joint further.
- Age. An adhesive joint worn daily for years can simply give up on an ordinary day; when that's all that happened, the pearl and peg may both be fine.
Pearl is soft, too: GIA puts it at 2.5 to 3 on the Mohs scale, so the pearl itself picks up scratches and dents from the same knocks that loosen it.
How a jeweler reattaches a pearl
The work is mostly preparation, and none of it puts a torch near the pearl.
- Inspect first. Under magnification the jeweler checks the pearl around the drill hole for cracks or peeling nacre, the depth and width of the hole, and the peg: straight, sound at its base and the right length for the hole.
- Clean both surfaces. Old adhesive comes out of the drill hole and off the peg, so the new bond is made to clean surfaces rather than to a layer of failed glue. A smooth peg may be twisted, as the Orchid bench advice describes, so it grips.
- Repair the metal before the pearl goes back. If the peg is bent, cracked or gone, or the post behind the cup has failed, that's metalwork, and it's done with the pearl off. GIA's warning about heat is the reason: a pearl left on during soldering can be burned, discolored or cracked.
- Set and cure. Fresh epoxy goes into the hole, not over the pearl's surface. The pearl is pressed home, turned so its best face shows and the drill hole is hidden, and left undisturbed to cure fully before it's cleaned and checked.
- A hole that's too large or damaged sometimes needs a fresh hole. The bench advice on Orchid is to drill slowly at low speed and keep the pearl cool with drops of water, because a hot pearl is a damaged one.
When it can't simply be reattached, and the alternatives
- The pearl is lost. GIA lists seven value factors for pearls: size, shape, color, luster, surface quality, nacre quality and, for jewelry with two or more pearls, matching. A replacement for one stud has to match its partner on all of them, and a ring pearl also has to fit the cup and peg. Sourcing is a quote, not a promise. For earrings, a new matched pair is sometimes the better answer; for a ring, so is a redesign through Custom Work & Modifications, which starts with a $10 estimate.
- The pearl is cracked, peeling or worn through. Resetting a damaged pearl just puts a damaged pearl back. GIA notes that if the nucleus is visible under the nacre, the nacre is likely thin; see can damaged pearls be repaired?
- The post or peg snapped. On an ordinary stud that's a post repair, covered in can a broken earring post be fixed? On a pearl stud, ask for a quote first, because the pearl has to come off before any soldering.
- A fashion piece. Imitation pearls and plated metal can cost more to repair than to replace. A free photo quote tells you which side of that line you're on before you ship anything.
Can I glue it back myself?
You can, and on an inexpensive pair it may be reasonable. On a pearl you care about, a home repair is often the start of a harder one. The problems are practical:
- The wrong adhesive. Bench jewelers use jeweler's epoxy made for the job. Whatever glue is in the kitchen drawer may not be made to bond metal to pearl.
- Glue on the nacre. Excess that squeezes out of the hole onto the surface dulls it, and because GIA notes pearls are damaged by many chemicals, cleaning it off carries its own risk.
- Residue left behind. A failed home repair leaves hardened glue in the drill hole and on the peg, and all of it has to come out before a proper reset.
- Heat. Never warm the glue, the pearl or the metal to speed things up.
If you go ahead anyway, the sourced bench points are the ones above: jeweler's epoxy rather than household glue, clean surfaces in the hole and on the peg, and no heat. The risk is yours, and a failed attempt adds cleanup to the eventual professional reset. See also can I glue a stone back into my ring?
What it costs at JewelryRepair.com
Reattaching a pearl isn't a fixed-price repair, because the work depends on the pearl, the peg and whatever adhesive is already there. Two routes to a price:
- Free photo quote. Send clear photos of the pearl, the empty peg and the whole piece through the contact page; a jeweler replies with an itemized quote within 1 business day.
- Mail-In Evaluation, $19, credited in full toward the work you approve. Decline, and the piece ships back with the photos and findings.
Shipping is $30 round trip per order, so a pair of studs and a ring can share one box; insuring a $1,000 pair of pearl studs at full value adds $22.50 (2.5% of $900), both directions. At Sky Jewelry's New York studio, with over 50,000 repairs since 1989, a bench jeweler resets the pearl, a second jeweler checks it, and the work carries the 1-year workmanship guarantee. A pearl off a strand rather than a ring or earring is Pearl Restringing instead.
Before you ship
- Bag the pearl on its own in a small sealed bag, then put that bag with the jewelry. Mention the loose pearl in your order note.
- Don't clean it first. No soaking, no ultrasonic, no polish on the metal around the cup.
- Send both earrings if it's a pair, so the jeweler can match the reset pearl's height and angle to its partner.
- Keep the box from crushing the pearl: pearl is only 2.5 to 3 on the Mohs scale, so pad the bag firmly in a small sturdy box with nothing outside naming the contents. The prepaid UPS label is ready in your account.
Questions
How much does it cost to reattach a pearl to an earring?
Can I use super glue to reattach a pearl?
Why do pearls keep falling off my earrings?
Can a lost pearl be replaced in a ring or earring?
Is a loose pearl worth reattaching?
My pearl spins on its post. Does it need fixing?
Related
JewelryRepair.com · Over 50,000 repairs since 1989
More repair questions · Repair glossary · How online jewelry repair works · Full price list