Chains & clasps
Earring post
An earring post is the short, straight wire fixed to the back of a pierced earring that passes through the piercing. It is usually soldered to a small pad on the earring, and it holds the back in place, either with a notch that a friction back grips or with threads that a screw back turns onto.
From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )
What an earring post is
The post is a short length of wire, smoothed at the tip and soldered to a small pad or cup on the back of the earring. Unlike the back, it is never meant to come off.
- Friction posts are plain wire with a slight groove just short of the end, where a butterfly back's springy tabs catch.
- Threaded posts are cut like a tiny bolt, so a screw back turns on like a nut.
- Hinged closures: an omega back folds a hinged loop over the post's end behind the lobe; a lever back replaces the post with a curved wire and a hinged catch.
Post wire is sized in gauge, and a lower number means thicker wire: 20 gauge is 0.812mm, 18 gauge 1.024mm, 16 gauge 1.291mm. Jewelers on the Ganoksin forum mostly use 20 gauge, about 0.8mm, for ear wires, the usual thickness for everyday earring posts too, and two there describe 18- and 16-gauge posts that would not go through their own ears. A piercing settles around the wire you wear, so a replacement post has to match the old one: a thicker (lower-gauge) post can be a tight fit.
Length varies more. The jeweler who started a Ganoksin thread on post sizes found 3/8 inch (9.525mm) to be the standard; others there make posts 10mm long or cut them to the wearer's lobe. For posts that poke or fall short, see what to do when a post is too long, short or thick.
How earring posts fail
A post is thin wire in a soft metal, so most failures start as a bend: sleeping in studs, snagging on knitwear, pushing a back on at an angle. Straightening it at home does the real damage, because bending work-hardens metal; each bend and re-straighten leaves that spot stiffer until it snaps instead of bending.
The ends fail too. The solder joint at the pad can crack, so the post wobbles before it falls off; the notch near the tip wears smooth, so even a new back slides away; a screw back forced on at a slant flattens the threads. And on fashion jewelry, posts are sometimes only glued on, and glue gives no warning before it lets go.
Signs a post needs repair
- The post no longer stands square to the back of the earring, or its end curves off to one side.
- You can rock the post with a fingertip where it meets the pad, or a hairline shows at the joint.
- Even a brand-new back slips straight off, because the groove near the end has worn flat.
- The threads are flattened, so a screw back spins without biting.
- One post is shorter than its pair, which can mean it snapped and was filed down.
A post that has been straightened once already, or is bent sharply or right at the pad, should be replaced rather than bent back. A heavy pair that has always tipped forward is a different problem: a friction back can't support a heavy drop, so Earring Back Conversion, which swaps the fitting, is the job instead.
Earring post vs earring back
The post is the fixed wire on the earring; the earring back is the loose piece behind the lobe. To find the fault, fit a back you know is new. If it holds firm, only the old back had stretched, and new backs in the same metal solve it. If it still slips, or the post leans or moves at the pad, the post is the part to replace. If the back is lost rather than worn, how to replace a lost earring back covers matching one to your post.
Ear wires, the curved hooks on drop earrings, do the same job and are covered by Earring Post Repair too, with $20 added for the wire style.
How a post is replaced, and posts for sensitive ears
At the bench, the old post comes off flush with its pad, the area is cleaned to bare metal, and a replacement in the earring's own metal is soldered or laser-welded on at a right angle to the back; laser welding keeps the heat to a tiny spot when stones sit close by. A pearl stud that has come off its post is quoted free from photos sent through the contact page.
For sensitive ears, the post matters most, because it stays inside the piercing all day. The American Academy of Dermatology counts earrings and their backs among the biggest culprits in nickel allergy and, for people who react, suggests surgical-grade stainless steel, 18-, 22- or 24-karat yellow gold, pure sterling silver or platinum. A new post here is made in the earring's own metal, so a gold, platinum or silver pair gets a matching post; if your ears react to a plated or fashion pair, raise it in the on-site chat before ordering: a new post in that same plated metal may not end the reaction.
What it costs here
Prices as listed on Nov 18, 2026, each with a clean and polish and the 1-year workmanship guarantee. On Earring Post Repair, gold builds on the $30 silver pair: 14K yellow $40 ($30 + $6 + $4), 18K yellow $43 ($30 + $6 + $7), 14K white or rose $45 ($30 + $11 + $4), platinum $104 ($30 + $74). The style charge follows the post the earring has now, so a 14K yellow screwback pair is $55 ($40 + $15). Plated and stainless steel pairs that need solder work are quoted free first through the contact page or the on-site chat, because heat and finishing can wear through a thin plated layer.
Include both earrings of the pair so the posts can be matched; UPS shipping is $30 round trip per order. Sky Jewelry, family jewelers on Lenox Avenue since 1989, is the New York studio behind JewelryRepair.com, with over 50,000 repairs since 1989; your earrings are photographed on arrival and before they ship back, and a second jeweler checks that the new posts sit straight.
Prices at a glance
| Service | Price | What's included |
|---|---|---|
| Earring Post Repair | from $30 a pair from $20 single |
A replacement post made in the earring's own metal and joined by solder or laser weld, with no glue. Plated and stainless steel pairs needing solder work are quoted free first. The style charge follows the post the earring has now: screwback +$15, wire +$20, leverback +$30, omega +$35. |
| Earring Back Conversion | from $40 | Changes the mechanism: clip-on to pierced, or friction posts to screwback or wire (+$30), leverback (+$40) or omega (+$60). Gold, platinum and stainless steel add a metal charge. |
| Mail-In Evaluation | $19 | For damage around the post, such as a cracked pad or a stone that loosened when the post bent. A jeweler examines the whole earring and quotes each fix with photos. |
Prices come from the live repair pages. Shipping is $30 round trip per order.
Related questions
Questions
What are earring posts made of?
What is the difference between a friction post and a threaded post?
What gauge are earring posts?
How long is a standard earring post?
Are earring posts and ear wires the same thing?
Why is my earring post wobbly where it meets the earring?
See also
All glossary terms · Repair questions · How online jewelry repair works