Bench techniques

Laser welding

Fine welding tip touching the prong of a round diamond solitaire

Laser welding joins jewelry metal with short, focused pulses of laser light that melt it at a pinpoint, often while adding metal matched to the piece. Because the heat stays concentrated, a jeweler can work close to stones, enamel or hollow metal that a torch would harm. It is used for prong tips, earring posts and hollow chains.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

How laser welding works

A jewelry laser welder concentrates light into a tiny spot. Laser beam welding in general reaches a power density on the order of 1 MW per square centimeter, which gives narrow welds, fast heating and cooling, and a small heat-affected zone. Jewelers fire it in short pulses: millisecond-long pulses are used to weld thin material, and pulsed welding tends to leave less porosity and spatter than a continuous beam. In a Ganoksin trade article, a Boston bench jeweler describes adjusting his beam from two-tenths of a millimeter up to two millimeters across.

Often the weld adds metal. At JewelryRepair.com, re-tipping a prong means laser-welding new metal matched to the setting onto the old tip. A Prong Rebuild goes further: what's left of the failed prong is removed to its base, and new wire matched to the setting's metal, karat and color is welded on and raised into a complete prong.

Where it's used here

The bench chooses laser or torch for each joint. The laser does the work on:

Laser welding vs soldering

Soldering joins metal with a separate, lower-melting alloy that a torch flows into the joint, warming the whole area around it. Laser welding melts the piece's own metal, plus any matching filler, at one small spot. Neither wins everywhere, and the bench picks per joint: Ring Resizing here is soldered, and solid cable and box chains take a torch solder. For the full comparison, see laser welding vs soldering.

Why it matters, and its limits

For you, the laser mostly means fewer compromises: a worn prong can be re-tipped with the stone in place, a hollow chain can be joined without crushing it, and a jump ring on a charm can be closed next to enamel. On a prong, the heat stays at the tip, right against the stone; the same Ganoksin article quotes a jeweler who can work as close as half a millimeter from heat-sensitive stones.

It isn't harmless, though. A designer in that article warns that lasers can damage diamonds, despite a common belief that they can't, so the bench decides case by case. A stone sitting right at the joint, or an old repair, can make any method risky. If something about your piece makes a weld look unsafe, work pauses and you get photos and an itemized update; nothing proceeds without your approval, and nothing beyond what you approved is charged.

What it costs here

  • Prong Re-Tipping: $29 for 1 to 4 prongs in silver; $53 in 14K yellow gold, $57 in 14K white or rose, $65 in 18K white and $224 in platinum. 5 to 9 prongs add $45.
  • Chain Soldering: from $30 for one break in silver. The hollow-chain option adds $20, so a hollow 14K yellow gold chain is $30 + $7 + $4 + $20 = $61. A hollow rope chain also carries the $25 rope charge: $75 in silver ($30 + $25 + $20) and $86 in 14K yellow gold ($30 + $7 + $4 + $25 + $20).
  • Charm & Pendant Soldering: $69; for several charms, the total is confirmed before work.
  • Earring Post Repair: from $30 a pair in silver, $40 in 14K yellow gold; a single earring is $10 less.
  • Shank Repair: from $45 for a crack or cut.

There is no laser line item: you book the repair, and its price is set by the metal and options on its page. The one related charge is Chain Soldering's hollow-chain option, +$20, since hollow chains are the ones laser-welded. The 1-year workmanship guarantee covers a joint that reopens. Sky Jewelry, family jewelers on Lenox Avenue since 1989, has done over 50,000 repairs since 1989.

Prices at a glance

Service Price What's included
Prong Re-Tipping from $29 silver, 1–4 prongs
$57 14K white, 1–4 prongs
New metal matched to the setting laser-welded onto each worn tip, then shaped back over the stone. 5 to 9 prongs add $45.
Chain Soldering from $50 hollow silver
$61 hollow 14K yellow
Hollow chains are laser-welded because torch heat can collapse them. These prices are for a hollow chain with no type charge, such as herringbone; a hollow rope chain adds the $25 rope charge, so $75 in silver and $86 in 14K yellow gold. A solid chain takes a torch solder, from $30.
Charm & Pendant Soldering $69 Charms attached permanently by soldering or laser-welding the link closed; delicate charms, enameled pieces and anything with stones get the laser. For several charms, the total is confirmed before work.
Earring Post Repair from $30 silver pair
$40 14K yellow pair
Broken post removed flush, the pad cleaned to bare metal, and a new post soldered or laser-welded on straight; never glued. A single earring is $10 less.
Shank Repair from $45 silver, crack or cut A cracked or cut band closed: laser welding where stones or delicate details sit near the seam, a torch where the piece allows.

Prices come from the live repair pages. Shipping is $30 round trip per order.

Questions

What is laser welding in jewelry repair?
It's joining metal with short, focused laser pulses that melt it at a pinpoint, often while adding metal matched to the piece. Because the heat stays local, a jeweler can weld near stones, enamel or hollow metal that a torch could damage. At JewelryRepair.com it's used for prong re-tipping, hollow chains, delicate charms, earring posts and ring shanks near stones; Prong Re-Tipping starts at $29 for one to four prongs in silver.
Is laser welding better than soldering?
Neither is better for every job. A laser keeps heat in a tiny spot, so it suits prongs on set stones, hollow chains and pieces with enamel. Torch soldering flows a separate alloy into the joint and still suits larger joins: Ring Resizing here is soldered, with sizing stock matched to the ring's karat and color. The bench picks the method; there's no laser line item, though hollow chains carry Chain Soldering's $20 hollow option.
Can platinum or white gold be laser welded?
Yes. Prong Re-Tipping, which laser-welds new metal onto worn tips, is offered in both at JewelryRepair.com: $57 for one to four prongs in 14K white gold and $224 in platinum. A hollow 14K white gold chain with one break is $68 through Chain Soldering ($30 + $14 + $4 + $20). If you're unsure whether other platinum or white gold work suits the laser, start with the $19 Mail-In Evaluation, credited in full toward the repair.
How much does laser welding jewelry cost?
There's no laser line item at JewelryRepair.com; you pay for the repair, priced by its metal and options. The one related charge is Chain Soldering's hollow-chain option, +$20, so a hollow silver chain with one break is $50, or $75 if it's a hollow rope chain. Prong Re-Tipping is $29 for one to four prongs in silver, Charm & Pendant Soldering is $69, and Earring Post Repair starts at $30 a pair.
Will a laser-welded repair show?
Usually not once it's finished. The laser fuses the piece's own metal, and any metal it adds, such as a new prong tip, is matched to the setting, so the seam isn't a second alloy. The joint is then shaped and finished, and every repair here includes a clean and polish. A jeweler quoted by Ganoksin calls laser work a neat and clean repair. Your piece is photographed on arrival and before it ships back, so you can compare.

All glossary terms · Repair questions · How online jewelry repair works

Sources