Chains & clasps
Jump ring
A jump ring is a single loop of wire with one seam where its two ends meet. It is the connector that lets a charm, pendant or clasp hang and move on a chain or bracelet. Twisted shut, the seam can work open with wear; soldered at the bench, the ring becomes a closed loop that cannot pull apart.
From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )
What a jump ring is
A jump ring is the simplest connector in jewelry: a circle of wire with one cut through it. Jump rings are made by coiling wire around a rod called a mandrel and cutting the coil into separate rings, so each ring has two ends that meet at a seam. The thickness of the wire is its gauge, and the gap left by the cut is called the kerf.
You will find jump rings wherever two parts need to hang or move against each other: between a clasp and the end of a chain, at the top of a charm, between a pendant and its bail, and between the sections of a link bracelet or a drop earring. Most people only notice one when it opens and something falls off; if that has happened to a pendant, see broken pendant bail repair as well.
How a jump ring fails
An open jump ring is held shut only by the stiffness of its own wire. Every snag on a sweater and every swing of a heavy pendant pushes on the seam, and thin or soft wire slowly gives: the ends drift apart, the ring stretches toward an oval, and the charm or chain slips through the gap. A charm can go missing this way while the bracelet itself stays intact.
Squeezing the ring shut with pliers brings the ends back together, but it leaves the same unjoined seam that opened the first time, so the same force can open it again. Prying the ends straight apart to slip something on, instead of twisting them, also bends the ring out of round, and the ends rarely meet flush afterward. The lasting fix is done at the bench: the ends are aligned under magnification and solder is flowed through the seam, so the ring becomes one continuous loop that cannot pull open. A ring that is stretched or made of thin wire is replaced with a heavier one.
How to tell a jump ring needs attention
- You can see a gap at the seam. Hold the piece under a bright light. If light shows between the two ends, a fine chain or a thin charm loop can work its way through.
- The ring is no longer round. An oval or lopsided ring has been pulled open at least once and is likely to open again.
- A charm or clasp sits at an odd angle. A ring that has spread a little lets the parts twist and catch on each other.
- It was closed at home. A pliers fix can hold for a while, but only solder turns the seam into a closed loop.
If the jump ring looks sound but the piece still comes loose, the weak point may be the clasp or the bail instead. The repairs listed on this page cover all three.
Jump ring vs split ring
A split ring is built like a tiny keyring: one piece of wire wound into a double loop. To attach something, you pry one end away from the coil with a single pair of pliers and turn the part around until it sits on the ring.
A jump ring is a single loop with one seam. It is opened by twisting the ends sideways with two pairs of pliers, one end toward you and one away, and closed by twisting them back until they meet flush. Left open, that seam is where a snag or a swinging pendant can push the ends apart.
Bead suppliers sell a third kind, the soldered ring, which has no opening at all: parts are slid onto it rather than opened and closed. A jump ring soldered shut at the bench ends up the same way. On a piece you already own, the practical choice is between leaving the jump ring as it is and having it soldered; JewelryRepair.com solders the ring that is there, or replaces it with a heavier one if it is stretched or thin. For when soldering is the better call, see solder charms or leave them on jump rings?
What jump ring repair costs here
At JewelryRepair.com, Jump Ring Repair starts at $19 for one ring in sterling silver. Yellow gold adds $7 and white or rose gold $8; 14K adds $5 and 18K adds $11, while 10K adds nothing. One 14K yellow gold ring is $31 ($19 + $7 + $5), and one 18K white gold ring is $38 ($19 + $8 + $11). Platinum adds $50 and stainless steel $15. Choosing two rings adds $20, three adds $35 and four adds $50.
When a charm with enamel or stones hangs on the ring, Charm & Pendant Soldering ($69) closes the link with a pinpoint laser weld, so the heat stays away from the parts that cannot take it. Not sure which part failed? The Mail-In Evaluation is $19, credited in full toward the repair: a jeweler examines the whole piece under magnification and sends an itemized quote with photos.
Shipping is $30 round trip by UPS per order, however many pieces are in the box, so a jump ring can travel with another repair. A bench jeweler at Sky Jewelry's New York studio does the work, a second jeweler checks it, and it is covered by the 1-year workmanship guarantee. JewelryRepair.com is run by Sky Jewelry, a family of jewelers on Lenox Avenue with over 50,000 repairs since 1989.
What it costs here
| Service | Price | What's included |
|---|---|---|
| Jump Ring Repair | from $19 sterling silver $31 14K yellow gold |
One jump ring aligned under magnification and soldered into a continuous loop, or replaced with a heavier ring if the original is stretched or thin. Two, three or four rings add $20, $35 or $50. |
| Charm & Pendant Soldering | $69 | Charms attached permanently by soldering or laser-welding the connecting link closed, so they still swing but cannot come off. Broken charm loops can be rebuilt; for several charms, the total is confirmed before work. |
| Clasp Replacement | from $48 | When the clasp itself has failed: a spring ring, lobster or box clasp soldered on and action-tested, or the original repaired when it can be saved. |
| Bail Repair | from $39 | When the loop at the top of the pendant is cracked or worn thin: the bail is soldered, rebuilt or replaced so the pendant hangs straight. |
Prices come from the live repair pages. Shipping is $30 round trip per order.
Related questions
Questions
Can a jeweler solder a jump ring closed?
How do you open a jump ring without breaking it?
Why does my pendant keep falling off my chain?
What is the difference between a jump ring and a split ring?
How much does jump ring repair cost?
See also
All glossary terms · Repair questions · How online jewelry repair works