Repair questions · Chains, clasps & bracelets

Why did my pendant fall off the chain, and can the jump ring be soldered shut?

Usually because the small jump ring holding it pulled open, or the bail wore through where the chain rubs. Yes, a jeweler can solder that jump ring into a closed loop that can't open again, or replace it with a heavier one. At JewelryRepair.com that's $19 in sterling silver and $31 in 14K yellow gold.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

$19Jump Ring Repair, one ring soldered shut in sterling silver
$31the same in 14K yellow gold ($19 + $7 + $5)
$39Bail Repair in silver, when the loop the chain runs through has worn or split
50,000+repairs since 1989 by Sky Jewelry's bench jewelers in New York

The short version

  • A pendant can only leave a closed chain through an opening: a jump ring that spread, a bail that wore through or opened, or a chain or clasp that let go so it slid off the end.
  • Soldering turns the ring into one continuous loop with no seam to open. That's Jump Ring Repair, from $19.
  • Heat-sensitive pendants with enamel or delicate stones near the ring: say so in your order, or start with the $19 Mail-In Evaluation, so the bench can choose the method.

Prices

Service PriceWhat's included
Jump Ring Repair from $19One ring soldered closed, or replaced with a heavier ring if it's stretched or thin. Silver $19; 14K yellow $31; 14K white or rose $32 ($19 + $8 + $5); 18K yellow $37 ($19 + $7 + $11); platinum $69. A second ring adds $20.
Bail Repair from $39A split bail soldered and re-rounded, or a worn one rebuilt or replaced so the pendant hangs straight. 14K yellow gold $63 ($39 + $20 + $4).
Charm & Pendant Soldering $69Only if you want the pendant fixed at one spot on the chain: the link is closed by soldering or laser-welding at the position you choose; it still swings.
Clasp Replacement from $48When the pendant slid off because the clasp opened: a spring ring, lobster or box clasp soldered on and action-tested, or the original repaired.
Mail-In Evaluation $19Can't tell what failed, or the pendant has a pinch, glue-on or hinged bail: itemized quote with photos, credited in full.

First, find what let go

Lay the necklace on a white cloth under a bright light and work from the pendant outward.

  • The jump ring between pendant and bail. Many pendants hang from the bail by a small separate ring. A visible gap at its seam, an oval or lopsided shape, or a ring that's simply gone means it opened.
  • The bail. Check the inside top of the loop, where the chain slides every day. A thin, shiny flat spot, a hairline crack or a bail pulled out of round is wear from the chain. Some bails aren't soldered at all: pinch bails grip a drilled stone with prongs, glue-on bails are bonded to the back, and snap-on and hinged enhancer bails open by design.
  • The chain and clasp. If the pendant's own connections are intact, it slid off an end. Look for a broken link, or a clasp that opens by itself: a spring ring that has lost its snap, or a lobster whose lever doesn't close all the way.
  • The ring at the clasp. The small ring joining the clasp to the chain is the same kind of open ring and fails the same way.

Keep whatever you find, even a bent ring. It shows the jeweler the size and wire thickness that failed.

Why jump rings open, and the types you'll see

Every jump ring starts as a coil of wire wound on a mandrel and sliced into individual rings, which is why each one has a seam where its two cut ends meet. Nothing holds an open ring closed except the springiness of the wire. A pendant swinging as you walk, a chain caught on a scarf, a clasp tugged around to the back of the neck: each one levers the ends a fraction apart, and a thin or soft ring eventually opens wide enough for the bail to slide out.

  • Open jump rings are the standard connector.
  • Soldered, or closed, rings are joined at the seam, so there's nothing to open or close and nothing can slip through.
  • Split rings are a double coil, like a tiny keyring. There's no single open seam, but they're bulkier, and a soldered ring has no opening at all.

Soldering the ring you already have keeps the original look and turns it into the closed type.

Can the pendant be soldered to the chain?

Yes, in two different ways, and it's worth knowing which one you're asking for.

  • Close the connection, keep the pendant free. Soldering the open jump ring, or rebuilding a worn bail, means the pendant can't come off its bail. It still slides on the chain and comes off over the clasp end when you want to change chains, as long as the bail fits over the clasp. That's Jump Ring Repair or Bail Repair.
  • Fix the pendant at one link. Charm & Pendant Soldering closes the connecting link around a chain link at the position you choose, so the pendant still swings but can't slide or leave.

Fixing it in place has trade-offs. You can't move the pendant to another chain, or wear the chain alone, without the link being cut; all of the pendant's weight hangs from one chain link. If you like to swap chains, close the connection instead.

How a jeweler solders a jump ring shut

At the bench, the jeweler brings the two cut ends together under magnification until there's no gap, flows solder through the seam, then files and polishes the joint until the ring reads as one unbroken circle. If the ring is stretched or made of thin wire, it's replaced with a heavier one rather than soldered. A jeweler confirms at intake whether anything needs to come apart, and you approve any change before work begins.

Heat is the thing to plan around. A torch warms the area around the joint, so if the pendant has enamel or delicate stones close to the ring, note it in your Jump Ring Repair order, or start with the Mail-In Evaluation ($19, credited in full) so the bench can pick the method. Jump Ring Repair lists stainless steel; plated and titanium pieces needing solder are routed by the Start a Repair wizard to a free quote (through the on-site chat or contact form) first; see soldering plated or stainless jewelry.

Can I do it myself?

You can close an open jump ring as a stopgap. Grip each side of the seam with a pair of flat-nose pliers and twist the ends back sideways until they meet flush; don't squeeze the ring or pull the ends straight together. It will hold for a while, but the seam is still open, so the same force can open it again, and glue doesn't make a metal joint. Don't solder next to a pendant at home: torch heat reaches stones and enamel, and soft solder has to be removed before a proper joint can be made. See whether you can solder jewelry at home.

What it costs at JewelryRepair.com, and before you ship

The table on this page has every metal; the two combinations people ask about most: soldering both the pendant ring and the clasp ring on a 14K yellow gold necklace is $51 ($31 + $20 for a second ring), and a pendant ring plus a small 14K yellow lobster clasp is $31 + $67 = $98, plus $30 shipping, $128 in all. A solder joint that reopens within a year is redone at no charge under the 1-year workmanship guarantee.

Before you ship:

  • Send the pendant and chain together, even if only one part failed, so the jeweler can check both and match the new ring to the chain.
  • Say in your order notes which part let go, whether the pendant has enamel or stones near the ring, and where you want it if you're having it fixed in place.
  • Not sure what failed? The Mail-In Evaluation is $19, credited in full toward the repair.

Shipping is $30 round trip per order by UPS however many pieces are in the box, and the necklace is photographed on arrival and before it ships back. Sky Jewelry, the family jewelers on Lenox Avenue behind JewelryRepair.com, has done over 50,000 repairs since 1989, and a jump ring gets the same second-jeweler check as any larger job.

Questions

What if my pendant has enamel or stones near the jump ring?
Say so when you order, so the bench can choose a method that keeps heat off it. A torch warms the area around the joint, so note it in the Jump Ring Repair order, or start with the $19 Mail-In Evaluation, credited in full. A jeweler confirms the plan at intake and you approve any change before work begins. Charm & Pendant Soldering ($69) is only for fixing the pendant at one spot on the chain.
Is a split ring more secure than a jump ring for a pendant?
For a pendant, a soldered jump ring is the most secure of the three, because it has no opening at all. A split ring is a double coil with no single open seam, but it's bulkier, and an open jump ring is held shut only by the springiness of the wire. Soldering the ring you have keeps the original slim look and costs $19 in silver at JewelryRepair.com, or $31 in 14K yellow gold.
My pendant has a pinch bail or a clip-on enhancer bail. Can it be secured?
Often, but it depends on the bail, so start with a look rather than a set price. Pinch bails hold a drilled stone with prongs that can spread, and snap-on or hinged enhancer bails are built to open. Our $19 Mail-In Evaluation, credited in full, gets you photos and an itemized quote. A plain soldered bail that has worn thin is Bail Repair, from $39 in silver.
Will soldering the jump ring stop my pendant from falling off for good?
It closes the most common opening, but the pendant can still leave if the chain breaks or the clasp opens and it slides off the end. Check the clasp while you're at it: a spring ring that has lost its snap or a lobster that won't close fully is Clasp Replacement, from $48. Soldered joints at JewelryRepair.com carry a 1-year workmanship guarantee.