Jewelry repair questions · Chains, clasps & bracelets

Can I solder broken jewelry myself at home, or should a jeweler do it?

You can, but not with a soldering iron or the tin-lead solder sold for electronics. Gold and silver are joined with hard solder that flows above 450 °C, which takes a torch, flux and an acid pickle, and the heat can fracture some gems. For a piece you care about, JewelryRepair.com solders a silver chain break for $30.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

450 °Cwhere soft solder ends and hard soldering begins
$30Chain Soldering, one break in sterling silver
$19Jump Ring Repair, soldered closed in silver
50,000+repairs since 1989

The short version

  • An electronics iron won't do it. It can't get a gold or silver seam hot enough for hard solder, and silver carries heat away faster than any other metal.
  • Soft solder is the wrong metal. Tin-based solders dissolve gold into a brittle joint, and they dissolve silver too.
  • A failed home fix makes the real repair harder. Lead or tin left on the piece has to come off before a jeweler can heat it.
  • Heat is the other risk. GIA warns that excessive heat and sudden temperature changes can fracture some gems; pearls can dry out and opals can crack.
  • Hobby silversmithing is different. Soldering new sterling work with a torch, flux and pickle is a learnable skill. Repairing a worn, stone-set or plated piece is the hard version of it.

Prices

Service PriceWhat's included
Chain Soldering from $30One break in sterling silver; $41 in 14K yellow gold ($30 + $7 + $4). Torch solder for solid chains, laser weld for hollow ones (+$20). White gold includes rhodium re-plating of the repaired area.
Jump Ring Repair from $19A jump ring soldered closed or replaced with a heavier one, so a pendant can't slide off; $31 in 14K yellow gold ($19 + $7 + $5).
Charm & Pendant Soldering $69Charms attached permanently by soldering or laser-welding the link closed, so they still swing; broken charm loops can be rebuilt.
Earring Post Repair from $30Posts replaced by soldering or laser welding, never glue. $30 per pair in silver, $20 for a single earring.
Mail-In Evaluation $19For a piece that already has glue or soft solder on it: a jeweler examines it under magnification and sends an itemized quote with photos. Credited in full toward the repair.

Why an iron and electronics solder don't work on gold or silver

Jewelers and electricians both say "solder," but they mean different metals. Soft solder, the kind sold on a spool for electronics, melts between about 90 and 450 °C; classic 63/37 tin-lead melts at 183 °C (361 °F) and the common tin-silver-copper lead-free alloy at 217 °C. Joining above 450 °C is called hard soldering, silver soldering or brazing, and that is what a bench jeweler uses. Jewelry hard solders contain a high share of the metal being joined, so they pass assay.

A soldering iron can't put that heat where it's needed. Irons top out around 480 °C, at the very bottom of the hard-soldering range, and even in electronics a small iron loses too much temperature on a large connection. Silver has the highest thermal conductivity of any metal, so a band or a chain pulls heat away from the tip before the seam gets hot enough. The solder sits on the surface instead of flowing into the seam.

Soft solder on precious metal is worse than no repair. Tin-based solders readily dissolve gold and form brittle intermetallic joints; in tin-lead solder, about 4% dissolved gold is enough to embrittle the joint. When a jeweler later heats the piece to make a proper joint, any lead left behind can eat into the metal. Repair jewelers on Ganoksin's forum describe grinding, scraping or dissolving every trace of lead away first, because heated lead can ruin a gold piece.

What a proper solder repair takes

  • Fit. The two edges are aligned so they meet along the whole seam. Solder bridges a tight joint, not a gap.
  • Flux. Flux keeps oxides from forming while the metal heats and cleans the surfaces so the solder can flow.
  • Heat. A torch brings the area up evenly until the solder melts and is drawn into the seam. Near stones, enamel or hollow links, a laser welder puts the heat at a pinpoint instead.
  • Pickle. A dilute acid bath removes the oxide and flux left by heating. It's corrosive and needs careful handling and disposal.
  • Finish. The joint is filed and polished flush. Heating sterling can leave firestain, a subtle red-purple discoloration that has to be polished out, and white gold needs fresh rhodium over the repaired spot.

Fumes matter too. Some older silver solders contain cadmium, which gives off toxic fumes and needs ventilation; the EU has allowed cadmium brazing alloys only for aerospace and military use since December 2011. If you solder at home, buy cadmium-free solder and work with ventilation and eye protection.

Can I do it myself? An honest checklist

  • Learning to make silver jewelry: reasonable with a torch, a fire-safe surface, flux, pickle and practice on scrap first.
  • A plain sterling jump ring or link, no stones: possible if you already have that setup. Squeezing a jump ring shut with pliers is not the same fix: it leaves a butt joint that reopens under the same force that opened it.
  • Gold: the solder must match the karat and color or the seam shows, and a mistake costs gold.
  • Anything with stones, pearls, opals or enamel: not with a torch at home. Take the pendant off before heating anything near it.
  • Hollow chains: thin walls can collapse under torch heat; jewelers laser-weld them.
  • Plated, steel or titanium pieces: the Start a Repair wizard sends solder work on these to a free quote. If you already know the repair, the Chain Soldering page lists set prices for stainless steel ($48 for one break, $30 + $18) and gold-plated or fashion chains ($47, $30 + $17). Titanium is quoted.
  • Glue or "cold solder": solder works by melting into the joint, and these products set at room temperature without melting, so they hold like glue rather than forming a soldered seam. Glued posts fail, which is why posts are never glued here, and residue has to be cleaned off before a proper repair.

What it costs at JewelryRepair.com

Broken chains and open jump rings are among the most common jobs at Sky Jewelry, family jewelers on Lenox Avenue since 1989 with over 50,000 repairs since 1989. Through JewelryRepair.com, every solder job is done at the bench in the New York studio, never outsourced, and soldering is done by hand. Prices from the live repair pages, Nov 18, 2026:

Every price includes a clean and polish and the 1-year workmanship guarantee: a solder joint that reopens is redone at no charge. If an earlier home repair is on the piece, the arrival photos show the old glue or solder before anything is removed, and a second jeweler checks the new joint for strength and a flush finish before it ships back. Shipping is $30 round trip per order, however many pieces are in the box.

Questions

Can I use a soldering iron on silver or gold jewelry?
Not for a lasting repair. Electronics irons top out around 480 °C, barely past the 450 °C line where hard soldering begins, and silver draws heat away faster than any other metal, so the seam never gets hot enough. An iron can only melt soft solder, which makes a weak joint on precious metal and has to be removed before a jeweler can repair it properly.
Does cold solder work on jewelry?
No, not as a metal repair. Solder works by melting into the joint; "cold solder" sets at room temperature without melting, so it holds like glue rather than a soldered seam. On a post, clasp or chain link that takes everyday pulling, a glued joint is the one most likely to fail, and its residue has to be cleaned off before a jeweler can solder. Earring posts are soldered or laser-welded here, never glued.
How much does a jeweler charge to solder a broken chain?
$30 for one break in a sterling silver chain at JewelryRepair.com, and $41 in 14K yellow gold ($30 + $7 + $4). Hollow chains add $20 because they're laser-welded, and rope, Cuban, snake and tennis patterns carry their own charge. The price includes a clean and polish and the 1-year workmanship guarantee; shipping is $30 round trip per order.
Can a jeweler fix a bad home soldering job?
Often, if the metal underneath hasn't been eaten away. Soft solder and glue come off first, by grinding, scraping or chemical removal, because lead heated to gold-soldering temperatures can eat into the piece. The $19 Mail-In Evaluation at JewelryRepair.com gets a jeweler's look under magnification and an itemized quote with photos, credited in full toward the repair.
Is soldering jewelry at home safe?
It can be, with the right setup and precautions. You need a torch, a fire-safe surface, flux and a pickle bath, which is a dilute acid that's corrosive and needs careful handling and disposal. Buy cadmium-free solder, because some older silver solders give off toxic cadmium fumes, and work with ventilation and eye protection. Practice on scrap before touching a piece you care about, and never heat near stones, pearls or enamel.