Bench techniques

Annealing

Gold bangle being reshaped on a steel bracelet mandrel with a mallet

Annealing is heating metal to a set temperature, well below its melting point, then cooling it so it softens and bends without cracking. Bending, hammering, rolling or drawing gold, silver and platinum makes them harder and more brittle, called work hardening; annealing relieves that stress so the metal can be shaped further.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

What annealing does

Metal is made of tiny crystals, or grains. Every pass through a rolling mill, every hammer blow and every bend scrambles those grains and locks stress into them. The metal gets stronger and harder but loses ductility, which is called work hardening. Push it far enough and it stops bending and starts cracking.

Heat reverses that. As the metal warms, it first recovers, shedding much of the internal strain; then new, strain-free grains form and replace the distorted ones, a stage called recrystallization. The result is soft, ductile metal ready to be formed again. Hold it too hot or too long and the grains keep growing, which costs strength and makes a clean finish harder to get, so a bench anneal is a matter of minutes.

Annealing temperatures for jewelry metals

A bench jeweler usually anneals with a torch and judges the temperature by the color of the glow. Bench guidance from the jewelry supplier Stuller gives these targets:

  • Sterling silver: 1,100°F (593°C), a low red glow, then a water quench.
  • Yellow gold: 1,250°F (677°C), a low red glow, then a water quench. Red and green golds are softened the same way.
  • White gold: 1,350°F (732°C), a dull orange, then a water quench.
  • Platinum: 1,800°F (982°C), bright orange, then air cooling or a quench.

The same guidance sets how much each metal can be cold-worked before it needs annealing: up to 70% for silver and platinum, 60% for yellow and green gold, and only 50% for red gold, the copper-rich family that rose gold belongs to. Annealing too often causes trouble of its own, including cracking and flaking surfaces, so it's done when the metal needs it, not by habit.

Why it matters for repairs

Most jewelry that bends was work-hardened the moment it bent. A bangle squeezed by a car door or a ring crushed in a gym grip has a stiff, stressed zone at the bend: wrench it straight in one go, or flex it back and forth, and the strain gathers there until a hairline crack opens. So reshaping is done in small steps, and softening the hardened zone first gives it room to move.

  • Bangle Reshaping is the service here that includes annealing: if the bend has hardened the metal, that zone is softened with heat before the bangle is brought the rest of the way round, then checked under magnification for stress cracks.
  • Ring Reshaping brings a band back to round gradually on a steel mandrel, never flexing it back the other way, and inspects the shank under magnification for hairline cracks.

Heat has limits. Torch heat and stones don't mix well, which is why ring sizing here solders with a laser around heat-sensitive settings and saves the torch for pieces that can take it. Hollow bangles are the honest exception: many can be improved but not every one made perfect, and you'll hear which yours is after it's photographed on arrival.

How to tell metal has work-hardened

  • It springs back when you try to bend it, or takes far more force than it used to.
  • It has already been bent and straightened, at home or elsewhere.
  • You can see fine lines, a crease or a crack on the outside of the bend.
  • Stones near the bend have loosened, because a bent shank pulls at the settings above it.
  • A band worn thin has been pushed out of round more than once.

If any of these apply, stop bending it by hand: every extra bend adds stress, and the next may crack it. A crack that has already opened is a solder repair (Shank Repair on a ring), not a reshape.

Annealing vs tempering

Both involve heating and cooling, but they do different jobs. Tempering is a steel process: the steel is first quenched to make it as hard as it can be, then reheated to a temperature below its lower critical point to trade some hardness for toughness, so it's less brittle. Annealing softens metal. Quenching adds to the confusion: plunging hot steel into water hardens it, but gold and silver are routinely water-quenched straight after annealing and stay soft. Some silver and a few gold alloys can be deliberately heat-hardened afterward (Stuller gives 650°F, about 343°C, for 30 minutes), which is a separate step again.

Annealing is also different from soldering and laser welding. All three use heat, but soldering flows a filler alloy into a joint and welding fuses metal together, while annealing joins nothing; it only changes the metal's internal structure.

What it costs here

Annealing isn't sold on its own. Bangle Reshaping includes it where the bend has hardened the metal; the other repairs below handle bent or cracked bands. Prices from the live repair pages, Nov 18, 2026, with a clean and polish and the 1-year workmanship guarantee:

  • Bent bangle: Bangle Reshaping from $85 in silver as an open cuff; a closed bangle adds $10 ($95). A 14K yellow gold open cuff is $94 ($85 + $6 + $3).
  • Bent or oval ring: Ring Reshaping from $53 in silver, $62 in 14K yellow gold ($53 + $6 + $3), $75 in 14K white gold ($53 + $19 + $3). If the bend changed your size, sizing after the reshape adds $40.
  • If the bend has already cracked: Shank Repair from $45 in silver for a crack or cut.
  • Not sure what it needs? The Mail-In Evaluation is $19, credited in full toward the repair.

Shipping is $30 round trip per order by UPS; full-value coverage for a $1,000 bangle is $22.50 (shipping and insurance). Your piece is photographed on arrival at our New York studio and before it ships back, and a second jeweler checks the work. JewelryRepair.com is run by Sky Jewelry, family jewelers on Lenox Avenue since 1989, with over 50,000 repairs since 1989.

Prices at a glance

Service Price What's included
Bangle Reshaping from $85 Worked back to round on a bracelet mandrel in small increments; where the bend has work-hardened the metal, it's annealed to restore malleability before forming continues. Then checked under magnification for stress cracks, stones tested for tightness, and polished.
Ring Reshaping from $53 A bent or oval band moved back to round on a hardened steel mandrel in small increments, checked under magnification for hairline cracks, and every stone tested for tightness. Sizing after the reshape adds $40.

Prices come from the live repair pages. Shipping is $30 round trip per order.

Questions

What does annealing do to metal?
It softens it. Heating metal to its annealing temperature lets new, strain-free grains replace the ones distorted by bending or hammering, so the metal regains the ductility it lost to work hardening. Sterling silver anneals at about 1,100°F (593°C) and yellow gold at about 1,250°F (677°C). In repair, it lets a bent bangle be reshaped without cracking; Bangle Reshaping here starts at $85.
Why do jewelers anneal metal?
Because worked metal gets hard and brittle. Every bend, hammer blow or pass through a rolling mill makes gold, silver and platinum stiffer, and past a point they crack instead of bending. Annealing resets the metal so the jeweler can keep forming it. It's used both in making jewelry and in repairs such as reshaping a bent bangle, which starts at $85 here.
What is the difference between annealing and tempering?
Annealing softens metal; tempering toughens steel that has already been hardened. Tempering reheats quenched steel below its critical temperature to make it less brittle while keeping much of its hardness. Annealing heats gold, silver or platinum to relieve stress and restore ductility. Quenching differs too: water hardens hot steel, but gold and silver are often water-quenched after annealing and stay soft.
Can a bent bangle be reshaped without cracking it?
Usually, yes: the bangle is worked back to round in small steps and annealed where the bend has hardened the metal, then checked under magnification for stress cracks. Hollow bangles are harder to get perfect, and you're told what to expect after yours is photographed on arrival, before any work. Bangle Reshaping here starts at $85 in silver, plus $10 for a closed bangle.
Does annealing weaken gold or silver?
It makes the metal softer for a while, which is the point, but done correctly it doesn't leave the piece fragile, and the forming that follows hardens it again. The risk is overdoing it: heating too hot or too long causes grain growth, which costs strength and makes finishing harder, and annealing too often can lead to cracking. That's why a bench anneal is kept to a few minutes at the right color.

All glossary terms · Repair questions · How online jewelry repair works

Sources