Jewelry repair questions · Rings & sizing

Can a bent ring be fixed?

Usually, yes. A bent engagement ring or wedding band in gold, silver or platinum is worked back to round on a steel mandrel in small steps, checked under magnification for hairline cracks and loose stones, then polished. A cracked or worn-thin band needs solder or new metal, and tungsten can't be reshaped. Ring Reshaping at JewelryRepair.com starts at $53.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

$53Ring Reshaping for a sterling silver ring
$62Ring Reshaping in 14K yellow gold ($53 + $6 + $3)
$116Ring Reshaping in platinum ($53 + $63)
+$40sizing after the reshape, if the ring no longer fits

The short version

  • Most bent rings can be fixed. A bent wedding band or engagement ring in gold, silver, platinum or stainless steel is reshaped, not replaced.
  • It's done slowly, on a hardened steel mandrel in small increments, so the metal isn't bent back and forth.
  • Check the stones. A bent shank pulls at the settings above it, so a bent ring and loose stones often arrive together.
  • Cracks change the job. A crack is soldered; a band worn too thin gets new metal.
  • Tungsten doesn't bend. It's extremely hard but brittle, and cracks or shatters instead.
  • Don't squeeze it back by hand. That adds stress exactly where the metal is already weakest.

Prices

Service PriceWhat's included
Ring Reshaping from $53Band brought back to round on a steel mandrel, inspected for cracks and loose stones, then polished. Silver $53; 14K yellow gold $62 ($53 + $6 + $3); 14K white or rose gold $75 ($53 + $19 + $3); platinum $116 ($53 + $63); stainless steel $78 ($53 + $25). Sizing after the reshape adds $40.
Shank Repair from $45For a band that cracked when it bent: the break is cleaned, closed true and soldered. $45 in silver, $57 in 14K yellow gold ($45 + $7 + $5). A band worn too thin gets new metal: half band +$75 in silver or +$250 in gold and platinum; bands 4mm and wider add $40.
Stone Tightening from $50Stones loosened by the bend secured under 10x magnification, up to eight per order, with bent-open prongs pressed back over the stone: $50 silver, $55 yellow gold, $60 white gold, $85 platinum.
Mail-In Evaluation $19For titanium, plated or unusual rings, or when you're not sure what the damage is: an itemized quote with photos, credited in full toward approved work.

How rings get bent, and why it matters

Gold, silver and platinum are soft enough to bend, which is part of what makes them workable at all. Rings usually go out of round from a sudden squeeze or a blow: gripping weights or tools, catching a hand in a closing door, or bracing a fall. Engagement rings are especially exposed, because a slim band carries a heavy head on the hand that takes every knock. It's a known trade-off: where an impact would crack tungsten carbide, precious metals bend instead.

Three things happen when a ring bends:

  • The metal at the bend work-hardens. Gold, silver and platinum all get harder and less workable as they're deformed. Bending them back adds more stress at the same spot, and past a point, overworked metal cracks rather than bends.
  • The settings take the strain. A distorted shank pulls at the head and at any stones along the band. Prongs can open, channel walls can spread and pavé beads can lift, so stones loosen even if they don't fall out right away.
  • The fit changes. An oval ring presses unevenly and can feel tight in one place and loose in another; once it's round again, it may not be quite the size it was.

Thin bands bend most easily. A shank worn down at the bottom after years of wear is more likely to go out of round, and more likely to bend again after it's fixed.

How a jeweler fixes a bent ring

A jeweler first decides whether the band can be moved at all. Under magnification they look at the inside of the bend for fine cracks or a dull, wrinkled surface, and measure how thick the bottom of the shank still is; a band that has been worn thin, or that cracks as soon as it's touched, goes to shank repair instead of a reshape. On a ring with stones all the way around, the setter also looks at how the stones will behave, because forcing the band round can squeeze or open the seats along it.

The Ring Reshaping service at the JewelryRepair.com bench in New York then runs in four stages:

  • Intake. The ring is photographed on arrival and a jeweler confirms the job. If the scope changes, you approve it before work begins.
  • Rounding. The band goes onto a hardened steel mandrel and is coaxed back to round a little at a time, rather than forced in one push.
  • Inspection. The shank is examined again under magnification for cracks the bend may have opened, and the stones are checked for movement.
  • Finishing. The ring is polished, photographed again, checked by a second jeweler and shipped back.

In general bench practice, metal that has been worked hard may need annealing, heating it to soften it, before it's moved further. Stuller's guidance on rolling and drawing gold shows how much alloys differ: green and yellow golds can be cold-worked by up to about 60% before annealing, silver and platinum about 70%, and red gold only about 50%. That's one reason a bent red or copper-rich rose gold ring deserves extra care. If inspection finds a crack or anything beyond the reshape, work pauses and you get photos and an itemized update; nothing extra is done or charged without your approval.

When reshaping isn't the whole fix

  • A crack: Shank Repair cleans the break, closes the ring true and solders it, from $45 in silver or $57 in 14K yellow gold ($45 + $7 + $5).
  • A band worn too thin: soldering thin metal doesn't make it thicker, so the bottom of the band is replaced with new metal. A half band adds $75 in silver or $250 in gold and platinum; a full band adds $125 or $375. A 14K yellow gold half band under 4mm wide is $307 ($45 + $7 + $5 + $250); 4mm and wider adds $40.
  • Loose or missing stones: a lifted or bent-open prong is pressed back with Stone Tightening (from $50); a worn tip is re-tipped and a snapped prong rebuilt, each from $29 (Prong Re-Tipping, Prong Rebuild).
  • A ring that was cut off: that's a cut, not a bend, and Shank Repair covers ER cuts; see can a ring that was cut off be repaired?
  • Tungsten carbide: GIA notes tungsten is brittle, can crack or shatter under high impact, and can't be resized. It doesn't bend back; see can a cracked tungsten ring be repaired?
  • Titanium, plated or unusual metals: Ring Reshaping lists gold, silver, platinum and stainless steel, and GIA notes titanium rings are hard to resize. For anything else, start with the $19 Mail-In Evaluation, credited in full toward approved work.

Can I bend it back myself?

It's tempting to squeeze an oval ring round between your fingers or with pliers, and it's how a simple bend becomes a crack. Hand pressure and pliers concentrate force on the spot that has already work-hardened, they can't support the rest of the band, and pliers dent soft gold and silver. On a stone-set ring, squeezing the shank also flexes the head and the settings along the band, which can loosen stones. For what is and isn't reasonable to try, see what you can and can't safely try at home.

If a ring has bent, take it off, keep it in a small bag so a loosened stone can't go missing, and don't try to wear it round again.

What it costs at JewelryRepair.com

The table above covers silver, 14K and platinum. The other karats on the live Ring Reshaping page: yellow gold is $59 in 10K ($53 + $6) and $64 in 18K ($53 + $6 + $5); white or rose gold is $72 in 10K ($53 + $19) and $77 in 18K ($53 + $19 + $5). Each price includes the crack and stone check, a clean and polish, and the 1-year workmanship guarantee. If you're unsure whether the ring will still fit once it's round, choose Not sure for sizing: the jeweler confirms the fit on arrival, and the $40 sizing is added only if you approve it.

Before you ship

  • Note your ring size if you know it, and whether the ring fit well before it bent.
  • If a stone came out, seal it in a small bag inside the package so it travels with the ring.
  • Pack the ring padded and held still in a small rigid box, in a plain outer box with nothing on the outside naming the contents; the coverage requires it. The prepaid UPS label is ready in your account after checkout.
  • Shipping is $30 round trip per order, with $100 of coverage each way and a signature at both ends. Full value is 2.5% of the value above $100, one fee for both directions, up to $10,000: a $2,000 engagement ring is ($2,000 − $100) × 2.5% = $47.50.

The ring is photographed when it reaches the New York studio and again before it ships back. JewelryRepair.com is run by Sky Jewelry, family jewelers on Lenox Avenue who have completed over 50,000 repairs since 1989.

Questions

How much does it cost to fix a bent ring?
At JewelryRepair.com, Ring Reshaping is $53 for sterling silver, $62 for 14K yellow gold, $75 for 14K white or rose gold and $116 for platinum. That includes the crack and stone check, a clean and polish and a 1-year workmanship guarantee. Sizing after the reshape adds $40 if the ring no longer fits. Shipping is $30 round trip by UPS for the whole order.
Will reshaping change my ring size?
It can. A ring that has been squeezed oval may fit differently once it's round again, and a band that was already a little loose or tight may be worth sizing while it's on the bench. Sizing after the reshape adds $40 on the Ring Reshaping page. If you're not sure, choose Not sure: the jeweler confirms the fit when the ring arrives, and you approve any sizing before work.
Can a bent platinum ring be fixed?
Yes. Platinum is reshaped the same way as gold, on a steel mandrel in small steps, then checked for cracks and loose stones. Like gold and silver, it work-hardens when it's bent, so the jeweler moves it gradually. Ring Reshaping in platinum is $116 at JewelryRepair.com ($53 + $63), and if a platinum band has worn thin, Shank Repair can replace the bottom with new metal.
Can a bent tungsten ring be fixed?
No, because tungsten carbide doesn't really bend. It ranks about 9 to 9.5 on the Mohs scale but is brittle, and GIA notes it can crack or shatter under high impact and can't be resized. A tungsten ring that looks bent is more likely cracked, or made of another metal. If you're not sure what yours is, the $19 Mail-In Evaluation at JewelryRepair.com examines the whole ring and is credited in full toward any repair.
Is it safe to keep wearing a bent ring?
It's better not to. A bent shank pulls at the settings above it, so stones can loosen and fall out while you wear it, and the stressed metal at the bend can crack if it keeps flexing. An oval band also presses unevenly on your finger. Take it off, keep it in a small bag, and have it reshaped and checked; Ring Reshaping starts at $53.
Can a bent engagement ring with diamonds be fixed?
Yes. Ring Reshaping covers stone-set engagement rings and wedding bands, and the stones are checked after the band is rounded, because bending often loosens them. Loose stones are secured with Stone Tightening, from $50 in silver or $60 in white gold for up to eight stones. If stones run all the way around the band, the jeweler confirms the plan when the ring arrives and you approve any change first.