Jewelry repair questions · Rings & sizing
How do I find my ring size at home?
From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )
The short version
- Best home method: measure the inside of a ring that already fits the same finger, then convert millimeters to a size.
- Least reliable: string or a paper strip wrapped around the finger. GIA warns that string can stretch and paper is easily damaged.
- Printable and phone sizers are only right at true scale, so check them against a ruler or a ring that fits.
- Measure more than once, at room temperature, on the hand you'll wear it on, and check that the size clears your knuckle.
Prices
| Service | Price | What's included |
|---|---|---|
| Ring Resizing | from $45 | Sterling silver: $45 down, $50 up one size, +$35 for each further full size up. 14K yellow gold: $65 down ($45 + $13 + $7), $70 up one size. The ring's current size is measured at intake and confirmed with you; the size you want comes from you. |
| Ring Sizing Beads | from $40 | Two small beads soldered inside the band so a ring that clears the knuckle stops spinning; reversible. 14K yellow gold $62 ($40 + $17 + $5); a sizing bar in silver $240 ($40 + $200). |
Method 1: measure a ring that already fits
A ring that's comfortable on the finger you're sizing is the best reference you have: it already accounts for your knuckle and for how snug you like a ring to feel.
- Pick the right ring. Use one worn on the same finger of the same hand. A plain, thin band gives the cleanest number; a wide band sits differently, so its size may not carry over to a thin one.
- Measure the inside, not the metal. Lay the ring on a ruler marked in millimeters, or use calipers, and read the inside diameter from inner edge to inner edge across the widest point. Measuring across the outside adds the band's thickness twice and reads large.
- Measure twice, at right angles. Worn rings often go slightly oval. If the two readings differ, use the average.
- Convert: US size = (inside diameter in mm − 11.63) ÷ 0.8128. A ring measuring 18.5 mm works out to (18.5 − 11.63) ÷ 0.8128 = 8.45, so about an 8½.
- No ruler or calipers? Trace the inside edge on paper with a sharp pencil and measure the tracing, or take the ring to a jeweler, who can read it on a ring stick.
Method 2: measure your finger
With no ring to copy, you can measure the finger itself, but it's the method most likely to be off. GIA advises against wrapping string or paper around the finger: string can stretch, paper is easily damaged, and a wrap measures only where the ring sits, not the knuckle it has to pass.
- If you do it anyway, use a thin strip of paper rather than string. Wrap it snugly at the base of the finger, mark where it overlaps, and measure that length in millimeters: that's the circumference. US size = (circumference in mm − 36.5) ÷ 2.55, so 54.4 mm is about a 7.
- Then test the knuckle. Tape the strip into a loop at your mark and slide it over the knuckle. If it won't pass, the knuckle sets the size.
- A reusable plastic sizer, the kind with a numbered tail that threads through a buckle, beats paper; GIA says plastic sizers can give a fairly accurate measurement.
Printable, phone and tape-measure sizers: getting a usable number
Each of these can give a usable size, and each has one way to go wrong.
- Printable sizers: print at 100% or "actual size" with page scaling turned off, then check the printed scale bar with a ruler before trusting any reading. A page shrunk to fit the paper gives the wrong size.
- Circle charts are matched to a ring, not a finger: lay a ring that fits on the chart and pick the circle that matches its inside edge, not its outside.
- A soft tape measure gives the circumference in millimeters, which converts the same way: (mm − 36.5) ÷ 2.55. It has the blind spot GIA flags for string, measuring only where the ring sits, so check the knuckle too.
- Phone and on-screen sizers depend on the image being shown at true size. Calibrate it if it offers that step, check it against a ring that fits, and treat the answer as an estimate.
Reading the number: a few anchor sizes
In the US and Canada, size 0 is 11.63 mm across, and each full size adds 0.032 inch, about 0.81 mm, to the inside diameter and about 2.55 mm to the circumference, so a half size is roughly 0.4 mm across.
- US 5: about 15.7 mm across, 49.3 mm around.
- US 7: about 17.3 mm across, 54.4 mm around.
- US 10: about 19.8 mm across, 62.1 mm around.
UK sizes use letters and much of Europe uses the inside circumference in millimeters (ISO 8653). For every size and system, see ring size conversion: US, UK, EU and mm.
What throws the number off
- Temperature and time of day: GIA notes that fingers shrink in the cold and swell in the heat, that humidity and altitude play a part, and that a morning reading can differ from an afternoon one. Measure two or three times on different days, never right after coming in from the cold or out of a hot shower.
- Band width: GIA notes that rings with wide shanks usually need to be a bit larger, since they fit more snugly.
- Disagreeing readings: lean toward the larger one.
What your size means for a resize
At JewelryRepair.com, the mail-in repair service of Sky Jewelry in New York, the Ring Resizing page asks for your current and desired size, and the price follows from them:
- Sizing down in sterling silver is $45. Sizing up one size is $50, and each further full size up adds $35, so two sizes up in silver is $85 ($45 + $5 + $35).
- Bands 4 mm and wider add $46, so note the width as well as the size.
- At our bench, most rings can be resized about 2 to 3 sizes either way (see how much ring resizing costs). GIA lists pavé, channel-set, eternity and twisted bands among the rings that are hard to resize; see which ring metals can't be resized too.
- If the ring clears your knuckle and then spins, Ring Sizing Beads (from $40) are often a better fix than going smaller.
For every fix compared, see Ring too small or too big?
When to get measured in person
A careful home measurement is fine for most rings. Get measured on a jeweler's sizing gauge if the ring is wide or valuable, or if your readings don't agree; any jeweler can do it. In New York, walk-ins are welcome at 354 Lenox Avenue (Malcolm X Blvd), New York, NY 10027, Sunday to Thursday 10:00 AM to 7:00 PM (Friday hours are on the Contact page).
JewelryRepair.com is run by Sky Jewelry, family jewelers on Lenox Avenue since 1989. The family has completed over 50,000 repairs since 1989.
Questions
Should I size up or down if I'm between ring sizes?
Are printable ring sizers accurate?
How can I find someone's ring size without asking?
Is my ring size the same on both hands?
Can I send a ring for resizing if I'm not sure of my size?
Related
JewelryRepair.com · Over 50,000 repairs since 1989
More repair questions · Repair glossary · How online jewelry repair works · Full price list