Settings & prongs

Bar setting

Halo diamond ring held in a ring clamp while its stones are tightened

A bar setting holds a stone between two thin bars of metal, one on each side, leaving the stone's other two sides open to the light. Small grooves cut into the inner faces of the bars grip the stone's edge. It is used for single center stones and for rows of diamonds across wedding and eternity bands.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

What a bar setting is

In a bar setting, each stone sits between two short, upright strips of metal that run across the ring rather than along it. The setter cuts a groove, or notch, into the inside face of each bar, seats the stone's girdle (its widest edge) in the grooves, and tightens the bars against it. Nothing covers the stone from the other two directions, so light reaches it from the sides as well as the top.

Bar settings come in two main forms. On a solitaire, two bars standing perpendicular to the band hold a single center stone, most often a round brilliant, though other shapes are used. On bands, a row of round or baguette diamonds runs across the top or all the way around the ring with one bar between each pair of stones, so every inner bar holds two stones at once. The style also appears on three-stone rings, often with baguettes as the side stones.

How a bar setting wears or fails

A bar-set stone is held on only two sides of its edge, so everything depends on the bars staying straight and tight. A knock against a door frame or a weight plate can push a bar outward, and once it moves, the stone has room to rock. Because a row of stones shares its bars, one bent bar can loosen the stones on both sides of it. The open sides that let in light also leave each stone's edge exposed: one diamond guide counts this as a drawback, since less metal around the stone makes a chip a little more likely than in more enclosed settings.

The bars themselves are thin, and like any setting metal they wear with years of daily contact. Resizing is the other risk. The same guide warns that resizing a bar-set ring can be expensive or difficult, and it gets harder when the stones run down the sides of the band, because the cut and reshaping have to stay clear of the bars. That guide also suggests having a bar-set ring inspected at least once a year. A plain band under a single bar-set center stone is usually standard Ring Resizing, from $45; for stones down the sides, see whether a ring with diamonds on the band can be resized.

Signs a bar setting needs attention

  • A rattle. Hold the ring next to your ear and tap it gently. A faint click or rattle means a stone has room to move.
  • A gap you can see. Under a bright light, look for daylight between a stone's edge and the groove in its bar.
  • A stone that sits differently from its neighbors: tilted, lower, or turned slightly out of line in a row.
  • A bar that leans instead of standing straight and parallel to the next one.
  • A chip or nick on the exposed side of a stone, a sign the ring has taken a knock that may also have moved a bar.

A loose stone caught early is a tightening job. A stone that has already fallen out means matching, sourcing and setting a new one, which costs more, so it pays to check bar-set bands whenever you take them off.

Bar setting vs channel setting

Both hold stones with metal walls rather than prongs, which is why they are confused. In a channel setting, a row of stones sits edge to edge between two continuous walls that run along the band, enclosing the stones' sides. In a bar setting, short bars run across the band between the stones, so each stone is held on two sides and open on the other two. The bar setting shows more of each stone and lets in more light; the channel protects the stones' edges better.

They also fail differently. A channel loosens when one of its long walls spreads, and stones can then slide along the channel. A bar setting loosens where a single bar has been bent, which usually affects the one or two stones beside it. On our Diamond Setting page, channel is a listed setting style (+$10) and bar is not, so a missing bar-set diamond is priced by free quote or through the evaluation.

What it costs here

At JewelryRepair.com, Stone Tightening secures loose bar-set stones under 10x magnification from $50 in silver ($55 yellow gold, $60 white gold, $85 platinum); set the number of loose stones, up to eight per order, in the configurator. A stone that has tilted, sunk or come out but is still in your hands is Reset Loose Stone, $89 flat: the seat is re-cut level and the stone set square. If it came out, seal it in a small bag inside the package; if it is lost, the job becomes replacement plus setting.

A missing diamond is replaced with Diamond Setting, which starts at a $5 base plus $15 per side diamond or $60 per center diamond, with metal charges on top; the diamond is matched to its neighbors and quoted separately for your approval, or you supply it. Because bar is not one of the listed styles, ask for a free quote or start with the $19 Mail-In Evaluation, credited in full, for a missing stone, a bent bar or a bar-set band you want resized. For an engagement ring worn every day, The Anniversary Service ($199) is a yearly deep clean, magnified inspection, loose-stone tightening, re-rhodium on white gold and condition photos.

Shipping is $30 round trip by UPS per order, with $100 of coverage each way; a $2,500 bar-set band can be covered for its full value both ways for $60 (2.5% of the $2,400 above $100). JewelryRepair.com is the mail-in service of Sky Jewelry, family jewelers on Lenox Avenue since 1989.

Prices at a glance

Service Price What's included
Stone Tightening $50 silver
$55 yellow gold
$60 white gold
$85 platinum
Each stone tested for movement under 10x magnification and the loose ones secured the way the setting holds them; set the number of loose stones, up to eight per order, in the configurator.
Reset Loose Stone $89 One stone that has tilted, sunk or come out, if you still have it: the seat is re-cut level and the stone set square.
Diamond Setting from $5 A missing diamond matched to its neighbors and set; metal charges are added, and the diamond is quoted separately for your approval or supplied by you. Bar is not one of the listed setting styles, so the labor is confirmed by free quote or evaluation first.
Mail-In Evaluation $19 For a bent or cracked bar, a missing or chipped stone, or a bar-set band you want resized: examined under magnification, with an itemized quote and photos. The $19 is credited in full toward the repair.
The Anniversary Service $199 Yearly engagement-ring maintenance: deep clean, magnified inspection, loose-stone tightening included, re-rhodium on white gold and condition photos. Structural work beyond tightening is quoted separately.

Prices come from the live repair pages. Shipping is $30 round trip per order.

Questions

Are bar settings secure?
Reasonably, when the bars are straight and tight, though one guide rates them slightly less secure than more enclosed settings because two sides of each stone are open. Grooves cut into each bar grip the stone's edge, and another guide says a diamond in a well-made bar setting is very unlikely to be lost. The risk is a hard knock that chips a stone or bends a bar, loosening the stones on both sides. A yearly check under magnification catches movement early.
Can a loose stone in a bar setting be tightened?
Yes, if the stone still sits level in its grooves: the bar is closed back against the stone's edge under 10x magnification, and the stone sharing that bar is checked too, since one bent bar can loosen two. At JewelryRepair.com, Stone Tightening starts at $50 in silver. A tilted, sunk or fallen-out stone you still have (seal it in a small bag in the package) is Reset Loose Stone, $89 flat; if it is lost, it becomes Diamond Setting, quoted first.
Can a bar-set ring be resized?
Often, but it depends on how far the stones run around the band. A plain band under a single bar-set center stone is standard Ring Resizing, from $45. When bar-set stones continue down the sides, the cut and reshaping have to avoid them, so start with a free quote or the $19 Mail-In Evaluation, credited in full. A jeweler checks the stones near the cut and quotes it with photos first.
What is the difference between a bar setting and a channel setting?
A channel setting holds a row of stones edge to edge between two long walls that run along the band, enclosing their sides. A bar setting holds each stone between short bars that run across the band, leaving two sides open. Bar settings show more of each stone and let in more light; channels protect the edges better. A channel loosens when a wall spreads, a bar setting where one bar bends.
How much does it cost to replace a missing diamond in a bar setting?
At JewelryRepair.com, Diamond Setting labor starts at a $5 base plus $15 per side diamond or $60 per center diamond, with metal charges added, and the diamond is matched and quoted separately for your approval. Bar isn't one of the listed setting styles, so the exact labor is confirmed by free quote or the $19 Mail-In Evaluation, credited in full, before anything is set. Shipping is $30 round trip.

All glossary terms · Repair questions · How online jewelry repair works

Sources