Watches
Mechanical watch
A mechanical watch runs on a wound spring instead of a battery. The mainspring stores energy, a gear train carries it toward the hands, and an escapement releases it in even steps to a balance wheel that swings at a steady rate. It is wound by hand or, in an automatic, by the motion of your wrist.
From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )
How a mechanical watch works
- Mainspring. A coiled spring in a barrel stores the energy. In a typical watch a full wind runs it for roughly two days.
- Gear train. A chain of wheels carries that energy toward the hands and the escapement, turning on jewel bearings to cut friction.
- Escapement. Releases the gear train in small, even steps, one per beat (half an escape-wheel tooth each), and gives the balance a small push each time; this is the tick you hear.
- Balance wheel and hairspring. Swing back and forth at a fixed rate, commonly 21,600 or 28,800 beats an hour, and decide how fast the watch runs.
Mechanical watch vs automatic
An automatic watch is a mechanical watch that winds itself. A weighted rotor pivots as your wrist moves and winds the mainspring through gears, and a slipping clutch stops the spring from being overwound. So every automatic is mechanical, but not every mechanical watch is automatic: a manual-wind watch has no rotor and is wound by the crown. Many automatics can also be wound by hand to get them started. Self-winding watches date back to the 1770s, and the first self-winding wristwatch was patented in 1923. When you book a repair, both count as a mechanical movement.
Mechanical watch vs quartz
A quartz watch counts the vibrations of a quartz crystal, 32,768 a second in nearly all of them, and steps its hands with a small battery-powered motor. A typical quartz watch gains or loses about 15 seconds a month. Mechanical watches are less precise: the Swiss chronometer test run by COSC holds a mechanical movement over 20 mm across to an average daily rate of -4 to +6 seconds over its first ten days of testing, and that is a demanding standard. The quickest way to tell them apart is the seconds hand. A quartz hand usually jumps once a second; a mechanical one sweeps in small steps, several a second.
How a mechanical watch wears
A mechanical movement runs in oil, and oil doesn't last forever. As lubricants thicken, friction rises at the pivots and the escapement, timekeeping drifts and the watch eventually stops. Gaskets at the crown, case back and crystal dry out too, so a watch that was water resistant when new may not be now. Signs it is due for service:
- It runs noticeably fast or slow, or stops on and off.
- A manual watch no longer runs as long on a full wind, or an automatic stops while you're wearing it.
- The crown pulls out, spins without setting the time, or is missing: that's a Stem & Crown Replacement, from $75.
- Fog or water shows under the crystal. Stop wearing it; this gets a free diagnosis first, and you approve any work.
- It hasn't been serviced in five or more years.
Caring for a mechanical watch
- Wind it gently. Wind a manual watch at about the same time each day and stop when you feel resistance; never force the crown.
- Don't book a battery. A mechanical watch has none. If it has stopped, wind it a few turns first; if it still won't run, it needs a movement service.
- Check water resistance before you swim. If it hasn't been tested in years, a Water-Resistance Pressure Test ($175) documents what it can still handle.
- Clean the outside without opening it. Watch Cleaning & Detail ($185) lifts grime from the case and bracelet while the case back stays sealed.
What it costs here
A mechanical Watch Overhaul is $295 for most brands: the $195 base plus $100 for a mechanical movement. The movement is taken apart, cleaned ultrasonically, inspected under magnification, re-oiled with the correct lubricant at each point, regulated and resealed, and worn parts are flagged with their cost before anything proceeds. Some brands carry a surcharge shown on the repair page and on watch repair by brand. Overhauls can't be rushed and take longer than the roughly three weeks most repairs take.
If your watch is still under the maker's warranty or a service plan, check with the maker first, because an outside overhaul can void it. JewelryRepair.com is an independent repair service, not affiliated with any watch brand. The overhaul is done at the New York studio of Sky Jewelry, the family jewelers on Lenox Avenue behind JewelryRepair.com, with over 50,000 repairs since 1989, and shipping is $30 round trip by UPS.
Prices at a glance
| Service | Price | What's included |
|---|---|---|
| Watch Overhaul | from $295 mechanical | Full movement service for manual-wind and automatic watches: disassembly, ultrasonic cleaning, inspection, re-oiling, regulation and reseal. Some brands add a surcharge. Can't be rushed. |
| Water-Resistance Pressure Test | from $175 | Documented pressure-chamber test against the watch's stated depth rating; resealing is quoted if it fails. |
| Watch Cleaning & Detail | from $185 | Case and bracelet cleaned and detailed; the case back stays sealed and the movement isn't touched. |
| Stem & Crown Replacement | from $75 | New stem and/or crown with a gasket; winding, setting and date tested. |
Prices come from the live repair pages. Shipping is $30 round trip per order.
Related questions
Questions
How often should a mechanical watch be serviced?
Is an automatic watch a mechanical watch?
How much does it cost to service a mechanical watch?
How accurate should a mechanical watch be?
Does a mechanical watch need a battery?
Should I send a mechanical watch that's still under warranty?
See also
All glossary terms · Repair questions · How online jewelry repair works