Watches
Balance wheel
A balance wheel is the weighted wheel in a mechanical watch that swings back and forth at a steady rate, pulled back toward center on every swing by a fine coiled hairspring. Each swing lets the escapement release the gear train one step, so the balance sets how fast the watch runs, like a clock's pendulum.
From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )
How a balance wheel works
The balance is the part of a mechanical watch that actually measures time. It is a small, carefully poised wheel mounted on an axle, the balance staff, with a flat spiral spring, the hairspring (or balance spring), attached at its hub. Each push from the escapement turns the wheel until the hairspring stops it and sends it back past center the other way. A healthy balance travels about 270° either side of its resting point, roughly three-quarters of a turn each way.
Each swing's length in time depends on how the wheel's mass is spread and how stiff the hairspring is, so it is the balance, not the mainspring, that sets the rate. Each swing is a beat, counted per hour: 18,000 was the norm on older watches, 21,600 and 28,800 (6 and 8 beats a second) are the usual figures today, and 36,000 is rare. The regulator, a small lever on the outer coil, sets how much of the hairspring is free to flex: a shorter working length is stiffer and makes the watch gain, a longer one makes it lose.
What it's made of, and why that matters
A modern balance wheel is usually made of Glucydur, an alloy of beryllium, copper and iron that expands little with heat, and paired with a hairspring in an alloy such as Nivarox, chosen to reduce how much temperature changes the rate. Some recent hairsprings are made of silicon, which doesn't become magnetized. The spiral hairspring itself dates to the 17th century, credited to both Christiaan Huygens and Robert Hooke, and it made portable timekeepers far more accurate.
The staff turns on very fine pivots running in synthetic sapphire jewel bearings (see watch jewels). Those pivots are slender next to the weight of the wheel they carry, so a drop can snap them; before shock protection, a broken balance staff was a routine repair. Incabloc, introduced in 1934 by Georges Braunschweig and Fritz Marti, sets the balance jewels on a small lyre-shaped spring that lets them shift under impact and then return.
How it wears or fails
- Old oil. The balance pivots, and the escapement that drives the balance, both depend on oil. As it thickens and dries, friction eats into every swing: the balance travels less far (its amplitude, read on a timing machine), and the rate starts to wander.
- A hard knock. Shock protection helps, but a watch that stops right after a fall may have a bent or broken pivot.
- Magnetism. Magnets in phones, speakers, tablet covers and handbag clasps are rarely a problem at a normal distance, but resting a watch against a strong one can magnetize a steel hairspring. The coils cling to each other, and the watch suddenly runs very fast or very slow; badly affected watches stop. A watchmaker can usually demagnetize it. Dirt or oil on the coils, or a regulator that has been moved, can also make a watch run fast, so a fast watch isn't necessarily magnetized.
Signs the balance needs attention
- It suddenly gains or loses a lot after time against a strong magnet, such as a speaker or a magnetic clasp.
- It runs noticeably faster or slower than it used to, or stops on and off.
- It stops even though it's fully wound.
- It stopped after a drop or a knock and won't restart when wound.
- It hasn't had a full service in five or more years.
Don't open the case back or move the regulator yourself. A watch that runs fast or stops on and off gets a free diagnosis first through the Start a Repair wizard, and you approve any work before it begins. A watch that stopped after a drop or knock should start with the Mail-In Evaluation ($19, credited in full toward the repair), because a damaged pivot or staff has to be seen before it can be priced.
Balance wheel vs rotor
Through a display case back, two moving parts are easy to confuse. The rotor is the large half-moon-shaped weight on an automatic watch. It pivots as your wrist moves and winds the mainspring through gears, and it sits still when you do. The balance is the much smaller wheel that swings back and forth several times a second, whether you move or not. A manual-wind mechanical watch has a balance but no rotor.
A quartz watch has no balance (and most have no rotor). It counts the vibrations of a quartz crystal and steps its hands with a small motor. If a quartz watch stops, start with the Watch Battery & Pressure Check, $30 for most brands; quartz movements can also be fully overhauled, from $195.
What it costs here
Balance work is part of a full Watch Overhaul. A mechanical overhaul is $295 for most brands ($195 base + $100 for a mechanical movement); Omega is $310, Longines $315, Patek Philippe $395 and Rolex $495. Overhauls can't be rushed and take longer than most repairs; your promised-by date shows before checkout.
A broken staff or damaged hairspring isn't a standard menu item, so it goes through the Mail-In Evaluation first and is quoted with photos for your approval. If the watch is still under the maker's warranty or a service plan, check with the maker first, because outside service can void it. JewelryRepair.com is independent, not affiliated with or authorized by any watch brand.
Shipping is $30 round trip per order by UPS; full-value coverage for a $5,000 watch is $122.50, 2.5% of the $4,900 above the included $100 (shipping and insurance). The watch is photographed on arrival and before it ships back, and a second jeweler checks the work. JewelryRepair.com is run by Sky Jewelry, family jewelers on Lenox Avenue since 1989, with over 50,000 repairs since 1989.
Prices at a glance
| Service | Price | What's included |
|---|---|---|
| Watch Overhaul | $295 most brands $310 Omega $315 Longines $495 Rolex |
The movement is taken out and apart, cleaned ultrasonically, and the train, mainspring and jewels are inspected under magnification; then it is re-oiled with the correct oil at each point, regulated for accuracy and resealed. This is where balance service happens. Worn parts are flagged before anything proceeds. |
| Mail-In Evaluation | $19 | For a watch that stopped after a knock, or a balance you suspect is damaged: a jeweler examines the whole watch under magnification and sends an itemized quote with photos. Credited in full toward approved work. |
Prices come from the live repair pages. Shipping is $30 round trip per order.
Related questions
Questions
What does the balance wheel do in a watch?
What is the hairspring on a balance wheel?
Can a broken balance staff be repaired?
Is the balance wheel the same as the rotor?
What amplitude should a balance wheel have?
How often does a balance wheel need servicing?
See also
All glossary terms · Repair questions · How online jewelry repair works