Watches
Mainspring
The mainspring is the long, coiled ribbon of spring metal that powers a mechanical watch. Winding the crown, or the rotor of an automatic, coils it tighter inside a drum called the barrel, and as it slowly unwinds it turns the gear train that drives the hands. Battery-powered quartz watches don't have one.
From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )
How a mainspring works
Inside a mechanical watch the mainspring lives coiled in the barrel, a small toothed drum. Its inner end hooks onto an axle called the arbor and its outer end catches on the barrel wall. Winding turns the arbor and coils the spring tighter. As the spring lets go it turns the barrel, whose teeth drive the gear train, and the escapement releases that power in tiny, even steps to move the hands. Uncoiled, a watch mainspring is a long, thin strip: roughly 20 to 30 cm (8 to 12 inches) of metal only 0.05 to 0.2 mm thick.
Everyday movements are built to run well past a day on one full wind, so a watch wound once a day doesn't run down between windings. Seiko, for example, states that its 4R35 automatic runs for about 41 hours once fully wound. Reserves differ by movement, so check your watch's specification before deciding its reserve has shrunk.
Manual-wind vs automatic: why you can't overwind it
On a manual-wind watch you turn the crown until the spring is fully coiled and you feel it firm up; stop there rather than forcing it. An automatic is wound by its rotor as you move, and the outer end of its spring carries a bridle, a slipping clutch that grips the inside of the barrel by friction. Once the spring is fully wound, its pull overcomes that grip and the bridle slides round the barrel instead of coiling the spring any further, so an automatic can't be overwound. Seiko's instructions for the 4R35 put it plainly: turning the crown further will not break the spring.
A watch that stops while fully wound isn't overwound either. Watches are built to be wound all the way, and one that stops with a full spring has some other fault, usually dirt, dried oil or a damaged part in the balance. See can you overwind a watch? and how to wind an automatic or manual watch.
How a mainspring wears or fails
- It breaks. Every winding flexes the spring, and metal fatigue can eventually crack it. Before the 1960s a snapped mainspring was the repair watchmakers saw most; the spring alloys that replaced carbon steel after 1945 made breaks far rarer, though they still happen.
- It gets tired. An old spring can lose some of its force, so the watch runs for less time on a full wind than it used to. Checking the spring for wear is part of the overhaul.
- The oil dries out. Watch movements run in oil, and oil doesn't last forever. As it ages and dries, more of the spring's power is lost to friction before it reaches the balance, so the watch loses accuracy or stops early even with a healthy spring.
Signs the mainspring needs attention
- The watch no longer runs as long on a full wind as it used to, or an automatic stops overnight after a full day on the wrist (see why an automatic stops overnight).
- On a manual-wind watch, the crown turns freely with no build-up of resistance and the watch never starts. On an automatic, where the bridle slips by design, the telling sign is a watch that won't run even after winding and wearing. A broken spring is one cause; a fault in the winding parts or the stem can look the same (see why a watch won't wind).
- The watch runs only while you are actively winding or wearing it.
- It hasn't been serviced in five or more years.
Dried oil, the escapement or the balance can cause most of these too, so the spring is checked with the whole movement. If your watch has stopped, the Start a Repair wizard sends it to a free diagnosis first, and you approve any work before it begins. More in why did my watch stop working?
Mainspring vs hairspring
The two springs do opposite jobs. The mainspring is the power source: the large coiled spring in the barrel that stores the energy from winding. The hairspring, or balance spring, is a hair-fine spiral attached to the balance wheel; it makes the balance swing back and forth at a steady rate and so sets how fast the watch runs. Hairsprings are even shaped so the mainspring's weakening pull changes the timing as little as possible.
That gives a rough rule for symptoms. A tired or broken mainspring tends to make a watch stop early or not run at all. A hairspring problem shows up as poor timekeeping instead: watchmaker Ashton Tracy, writing in Quill & Pad, explains that magnetism makes a hairspring's coils cling together, which shortens its working length so the watch gains time, and that a magnetized watch can suddenly run very fast or very slow. See is my watch magnetized? The overhaul inspects the mainspring and regulates the watch for accuracy.
What it costs here
There is no set mainspring price at JewelryRepair.com. The spring is checked during a mechanical Watch Overhaul, $295 for most brands ($195 base + $100 for a mechanical movement). If it is worn or broken, the replacement is itemized with photos for your approval before a new spring is fitted, and nothing beyond what you approve is charged. Some brands add a surcharge, listed on watch repair by brand; the full breakdown is in how much a watch service or overhaul costs.
If the crown pulls out, spins without engaging or is missing, the fault may be the stem rather than the spring: Stem & Crown Replacement starts at $75. A quartz watch has no mainspring; if one stops, start with the Watch Battery & Pressure Check, $30 for most brands. If your watch is still under the maker's warranty or a service plan, check with the maker first, because an outside overhaul can void it. JewelryRepair.com is an independent repair service, not affiliated with any watch brand, and the mail-in service of Sky Jewelry, family jewelers on Lenox Avenue with over 50,000 repairs since 1989.
Prices at a glance
| Service | Price | What's included |
|---|---|---|
| Watch Overhaul | from $295 mechanical | Movement removed, taken apart and cleaned ultrasonically; train, mainspring and jewels inspected for wear under magnification; re-oiled, regulated for accuracy, gaskets checked. If the mainspring needs replacing, it is itemized with photos for your approval before a new one is fitted, and nothing beyond what you approve is charged. Some brands add a surcharge. Can't be rushed. |
| Stem & Crown Replacement | from $75 | When the crown pulls out, spins without engaging or is missing because the stem or crown has failed rather than the spring: new stem and/or crown with a gasket; winding, setting and date tested. |
Prices come from the live repair pages. Shipping is $30 round trip per order.
Related questions
Questions
What does a mainspring do in a watch?
Can you overwind a watch?
How do I know if my watch mainspring is broken?
How much does it cost to replace a mainspring?
What is the difference between a mainspring and a hairspring?
Why does my automatic watch stop overnight?
See also
All glossary terms · Repair questions · How online jewelry repair works