Jewelry repair questions · Watches

Why won't my watch wind, and can a broken mainspring be replaced?

A watch that won't wind usually has worn winding gears, a stem that no longer engages, or, especially in vintage watches with steel springs, a broken or slipping mainspring. A broken spring is normally replaced within a full service: at JewelryRepair.com a mechanical Watch Overhaul is $295 for most brands, with any new spring priced for your approval first.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

$295mechanical Watch Overhaul, most brands ($195 + $100)
$75Stem & Crown Replacement, most brands, when the stem is what broke
$19Mail-In Evaluation, credited in full toward the repair
50,000+repairs since 1989 by Sky Jewelry's family of jewelers

The short version

  • Rule out the simple causes first: a screw-down crown that hasn't been unscrewed, a crown left pulled out in the setting position, or a quartz watch, which doesn't wind at all.
  • Some automatics can't be hand-wound by design. Wikipedia's article on automatic watches gives Seiko's 7S26-based watches as an example. Turning the crown does nothing to the spring.
  • The crown spins freely with no resistance and the watch won't run: a broken mainspring, a failed click or worn winding wheels, or a stem that has snapped inside the case.
  • It winds but stops within hours: a tired spring, a bridle slipping too early in an automatic, or a dirty, dry movement.
  • The crown is hard to turn or stuck: a different fault; see why a crown is stuck or stiff.

Prices

Service PriceWhat's included
Watch Overhaul $295 mechanical
$195 quartz
Movement removed and taken apart, every part cleaned ultrasonically, the train, mainspring and jewels inspected under magnification, worn parts flagged before anything proceeds, then lubricated, regulated and resealed. Brand surcharges apply; it can't be rushed.
Stem & Crown Replacement from $75When the crown spins without engaging because the stem snapped or stripped: a new stem cut to your case, a matched crown and gasket, and winding, setting and date tested. TAG Heuer $195, Rolex $275.
Mail-In Evaluation $19A jeweler opens up the question you can't answer from outside: spring, winding parts or stem. Itemized quote with photos, credited in full toward the work you approve.
Watch Battery & Pressure Check from $30For a quartz watch, which never winds: a new battery, gasket inspection and pressure check. $30 for most brands.

How winding works, and where it fails

Turning the crown turns the stem, which drives a small chain of wheels, the keyless works, into the barrel where the mainspring lives. As Wikipedia's mainspring article sets out, the crown's turns reach the arbor at the barrel's center and coil the spring tighter around it. A toothed ratchet and a small spring-loaded catch, the click, hold that tension so it can't escape back through the crown. The spring then spends its energy by turning the barrel itself, slowly: in a common design one revolution takes about 8 hours, so a 40-hour reserve works out to 5 revolutions.

Each link in that chain has its own failure, and each feels a little different at the crown:

  • The spring breaks. Nothing builds tension, so the crown turns on and on.
  • The click or its spring fails. The spring can't hold what you wind into it, so it lets straight back down.
  • The winding wheels or clutch wear. The crown turns but the teeth don't engage. WatchesbySJX's keyless-works explainer calls these parts historic weak points, worn by yanking the crown or cycling its positions too often.
  • The stem snaps. The crown spins freely and won't set the time either. That's usually a broken stem or crown, not the spring.
  • An automatic's self-winding stops. The rotor drives the spring through reversing and reducing gears. If it runs after a crown wind but won't stay wound from wearing alone, those parts are the suspect; see why an automatic stops overnight.

Feel narrows it down; only the open movement proves which part failed.

Broken, tired or slipping: the three mainspring faults

Broken. Wikipedia's history of the mainspring notes that broken mainsprings were the largest cause of watch repairs until the 1960s. Carbon-steel springs failed from metal fatigue long before other parts, often at the end of winding when the spring was coiled tight, and sometimes from temperature changes. Since 1945, newer alloys have increasingly replaced carbon steel, and Wikipedia describes the risk of them breaking as minimal. So in a modern watch, suspect the winding parts first; in a vintage or pocket watch that may still carry its original steel spring, suspect the spring.

Tired. A spring that hasn't broken can still be set: after decades of use it deforms slightly and loses force, so the watch runs fewer hours on a full wind.

Slipping. An automatic can't be overwound because its spring isn't hooked to the barrel wall. TimeZone's Watch School glossary describes the bridle on the spring's outer end: below full wind it presses the outer coil into a notch in the barrel wall and holds; at full wind it jumps the notch and slides round to the next, shedding the extra tension. If that slip starts too early, the watch never reaches a full wind and runs short, a fault that shows only once the barrel is opened.

A spring that breaks can also do damage on the way out. When an old mainspring snapped, its outer part recoiled and spun the barrel backward; some movements used a motor barrel specifically so that recoil hit the winding parts rather than the wheel train. It's one more reason a broken spring means inspecting the whole movement, not just swapping the spring.

How a watchmaker replaces a mainspring

  • Let down the power. Whatever tension is left is released under control by easing the click while holding the winding. Wikipedia cautions that a spring still stores a hazardous amount of force even after it has been let down.
  • Take the movement out of the case, then lift out the barrel and open it.
  • Remove the old spring with a mainspring winder, a tool that coils the spring safely instead of letting it unwind across the bench.
  • Fit the right replacement: a spring matched to that barrel and that movement's design, including the bridle end on an automatic.
  • Service the rest. With the barrel out, the movement is most of the way apart anyway, and fresh power through a dirty, dry gear train won't keep good time. That's why spring replacement is normally done inside a full service.

At JewelryRepair.com that service is the Watch Overhaul: every component cleaned ultrasonically, the train, mainspring and jewels inspected under magnification, worn parts flagged before anything proceeds, then lubrication, regulation and reseal. Step by step: what happens during a watch overhaul.

Can I fix it myself?

Do the free checks: unscrew a screw-down crown fully, push the crown all the way in, wind clockwise, and confirm the watch is mechanical and hand-windable. Past that, leave it closed: opening the back lets in dust and can compromise water resistance, the spring is under tension, and replacements must match the barrel. Shaking or tapping won't free a broken spring. See how to wind a watch properly and whether you can overwind one.

What it costs at JewelryRepair.com

Live prices on Nov 18, 2026, each with the 1-year workmanship guarantee; the configurator shows the exact total before checkout.

  • Watch Overhaul, mechanical: $295 for most brands ($195 + $100 for a mechanical movement). With a brand surcharge: Omega $310 ($195 + $15 + $100), Rolex $495 ($195 + $200 + $100). Quartz is $195 for most brands. A new mainspring, like any replacement part, is flagged and priced for your approval before it's fitted. Overhauls can't be rushed.
  • Stem & Crown Replacement: $75 for most brands, TAG Heuer $195 ($75 + $120), Rolex $275 ($75 + $200).
  • Not sure which it is: start with a free quote through the on-site chat or the contact page, itemized within 1 business day. When the watch has to be opened to tell, the Mail-In Evaluation, $19, is credited in full: if it finds a broken spring in a mechanical watch of most brands, the overhaul costs $276 more ($295 - $19), plus the spring or any other part you approve.
  • A quartz watch that stopped: Watch Battery & Pressure Check, $30 for most brands.

A watch travels by UPS for $30 round trip, $100 covered each way and signed for at both ends; full-value cover on a $3,000 watch adds $72.50 (2.5% of the $2,900 above $100) for both legs. It's photographed when it reaches New York and again before the return, and a second jeweler checks the work.

JewelryRepair.com is an independent repair service, not affiliated with, authorized by or endorsed by Seiko, Omega, Rolex, TAG Heuer or any other watch brand, and we don't claim factory parts. If your watch is still under the maker's warranty or a service plan, check with the maker first, because an outside overhaul can void it. Behind JewelryRepair.com is Sky Jewelry, a family of Lenox Avenue jewelers with over 50,000 repairs since 1989.

Questions

How much does it cost to replace a watch mainspring?
At JewelryRepair.com the spring is replaced within a full Watch Overhaul, $295 for a mechanical watch of most brands, because the movement has to come apart either way; the spring itself, if one is needed, is priced for your approval first. Brand surcharges apply, for example $310 for Omega. Not sure the spring is the problem? Start with a free quote or the $19 Mail-In Evaluation, credited in full.
Can you break a mainspring by overwinding?
Not in normal use: watches are built to be wound fully, old steel springs broke mainly from metal fatigue, and automatics slip once full. Stop a hand-wound watch at firm resistance and never force it. Our answer to "Can you overwind a watch?", linked below, covers it in full.
Why is my automatic watch not winding when I wear it?
Usually too little wrist movement, or worn self-winding parts. Wind it fully by the crown, if your model allows, and see whether it runs its rated reserve off the wrist. If it does, the spring is fine and the rotor or its reversing gears are suspect; if it won't hold a crown wind, suspect the spring or barrel.
Why won't my pocket watch wind?
Check how it winds first: until the third quarter of the 19th century, pocket watches were wound with a key, not the crown. If the crown spins with no resistance on a stem-wind watch, an old carbon-steel mainspring may have broken, the largest cause of watch repairs until the 1960s. Pocket watches start with the $19 Mail-In Evaluation at JewelryRepair.com, credited in full.
Is it worth replacing the mainspring in an old watch?
Often, if the watch matters to you or holds value. The cost is the overhaul, $295 for most brands, plus the spring and any other parts you approve. The harder question is part availability for rare or unmarked movements, which nobody can promise unseen; the $19 Mail-In Evaluation gets you an itemized quote with photos first.