Jewelry repair questions · Chains, clasps & bracelets

Can a broken or kinked snake chain or box chain be repaired?

A break, usually yes. Box chain solders like most chains; snake chain is trickier, because heat can draw solder into its tight links and stiffen them. At JewelryRepair.com, by mail, one break is $30 in sterling silver box chain or $43 in sterling silver snake chain. Kinks start with a $19 evaluation.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

$30one break, sterling silver box chain
$43one break, sterling silver snake chain ($30 + $13)
$54one break, 14K yellow gold snake chain ($30 + $7 + $4 + $13)
50,000+repairs since 1989

The short version

  • A broken box chain is a routine solder repair: the link is closed with solder matched to the chain and polished flush.
  • A broken snake chain can be repaired too, but it's slower work, made with very little heat and solder.
  • A kink in a snake chain is the harder problem: often improved, not always invisible, and always a weak spot.
  • A snake chain that has slipped out of its end cap isn't a broken chain: the cap that carries the clasp needs reattaching.

Prices

Service PriceWhat's included
Chain Soldering from $30 sterling silver box chain
from $43 sterling silver snake chain
$54 14K yellow gold snake chain
One break rejoined and polished flush. Choose Box (no style charge) or Snake (+$13) as the chain type. Solid chains are torch-soldered with solder matched to the karat and color; hollow chains are laser-welded (+$20). A second break adds $17.
Chain Shortening from $57 1.5mm sterling silver snake chainFor damage near the clasp, if a shorter chain suits you: chain removed at the clasp end, the clasp re-soldered, and the removed piece returned to you. Snake adds $13; box adds nothing. Width adds $5 at 2mm up to $20 at 5mm.
Clasp Replacement from $48When the chain is sound but the clasp has failed: a spring ring, lobster or box clasp matched to the chain's gauge and soldered on, or the original repaired when it's salvageable.
Mail-In Evaluation $19For a kink, a twisted or crushed section, or a snake chain that has pulled out of its end cap: examined under magnification, with photos and an itemized quote. Credited in full toward approved work.

How snake and box chains are built, and why it matters

A box chain is made of squared-off links that look like little cubes. Jewelers of America describes box chain as extremely durable. Each link is a separate unit, so a break usually means one link has opened or torn, and the jeweler can close or replace it as on any link chain. The weak points are a link twisted out of square, often where a heavy pendant pulls, and the clasp end, where Cooksongold notes most chain wear happens because that's where the stress is.

A snake chain is built very differently. Jewelers of America explains that traditional snake chain is made from star-shaped stampings piggybacked one on top of the other to make a soft, supple chain. There are no gaps and no open links, which gives it that smooth, liquid look. It also means:

  • A break cuts across a tube of nested plates. The two ends have to be trimmed back to sound metal and joined so the chain still flexes on both sides of the joint.
  • Heat travels. On Ganoksin's Orchid forum, a bench jeweler explains that thin chain heats up and allows the solder to flow up the links, and another describes the first stretch of chain stiffening during soldering. That's why snake chain is joined with very little heat and very little solder, using heat sinks to keep the rest of the chain cool.
  • It kinks. A sharp bend forces the plates out of their nested positions, and they don't spring back on their own.
  • The clasp hangs from a cap. With no open link to hang it from, a snake chain ends in a small metal cap or tube that carries the clasp, and that joint can fail on its own.

Break, kink or end cap? How to tell

Lay the chain straight on a dark cloth in good light and run it slowly between your fingers.

  • Two separate ends: a break. On a box chain, look for an opened or torn link; on a snake chain, a clean cut or ragged plates. Book Chain Soldering with Box or Snake as the chain type.
  • A bend that won't lie straight, a sharp angle or a flattened ridge in a snake chain: a kink. The chain is in one piece but damaged at that spot.
  • The chain has pulled out of the cap at the clasp end, leaving the clasp and its cap on their own: an end-cap repair, not a chain break. Start with a free photo quote or the evaluation.
  • A twisted or stretched section of box chain, often near a pendant's bail: links pulled out of square.
  • A clasp that won't close on a sound chain is a Clasp Replacement (from $48), not a chain repair; a box clasp is a fastener, not a box chain.

How a jeweler repairs each one

Box chain. The damaged link is examined under magnification. If it has simply opened, it's aligned and soldered closed with solder matched to the chain's karat and color, then filed and polished flush. A torn or stretched link is cut out and the chain rejoined, which can shorten it by a link or two; White gold solder work includes rhodium re-plating of the repaired area.

Snake chain. The jeweler trims back to sound plates and rejoins the ends. Bench jewelers on Orchid describe cutting out the damaged section and soldering the ends with solder paste and very little heat, and say the job takes heat control and patience. Cooksongold admits snake chain can appear impossible to repair because of the way it's constructed, and calls soldering it tricky but possible. Expect the chain to come back a little shorter, and the joint may feel slightly firmer than the chain on either side.

What can be done about a kink

There's no listed kink-removal service, and that's deliberate. A kink in a snake chain is plates that have been bent out of their nest, and how far they'll go back depends on the chain. In a Ganoksin Orchid discussion of exactly this problem, the suggestion offered was to pull the chain through a hole in very hard wood matched to the chain's size, which may fix the kink or make it much less noticeable. That's the honest range: improved, sometimes close to invisible, sometimes not.

Two more things matter:

  • A kinked spot stays weaker. Metal that is bent and straightened work-hardens, becoming harder and less ductile, so a spot that has kinked and been worked back is more prone to crack later.
  • Cutting it out can be the better repair. If the kink sits near one end, or the plates have cracked, removing that section and rejoining the chain, or shortening it, gives you sound chain instead of a straightened weak spot.

Because the right answer depends on the damage, a kinked snake chain or a twisted section of box chain starts with the $19 Mail-In Evaluation: photos, a plain-English assessment and an itemized quote, with nothing done until you approve it.

Can I fix it myself?

Not a break. A snake chain has no open link to pinch shut, pliers crush its plates, and glue won't hold a joint that flexes with every movement. A box chain link can sometimes be squeezed closed with pliers, but an unsoldered link is a stopgap, not a repair, so don't trust a pendant to it.

For a mild kink, gentle is the rule: lay the chain on a flat surface and coax it straight with your fingers, never with pliers or a hammer, and stop if it isn't improving, because each time the same spot is bent back and forth it work-hardens further. For more, see how to get a kink out of a necklace chain.

What it costs at JewelryRepair.com

Chain Soldering is priced live by metal, chain type, number of breaks and whether the chain is hollow. Box chain adds nothing; snake chain adds $13. Prices from the live repair pages, Nov 18, 2026, each for one break, including a clean and polish:

  • Sterling silver: box $30; snake $43 ($30 + $13).
  • 14K yellow gold: box $41 ($30 + $7 + $4); snake $54 ($30 + $7 + $4 + $13).
  • A second break adds $17: two breaks in a 14K yellow gold snake chain are $71 ($54 + $17). A hollow chain is laser-welded for $20 more.
  • Chain Shortening, for damage near the clasp: a 1.5mm sterling silver snake chain is $57 ($44 + $13).
  • A kink, twisted section or loose end cap: the $19 Mail-In Evaluation, credited in full.

Other metals, white gold rhodium and rush timing are in the chain soldering cost guide. Sky Jewelry's New York bench, with over 50,000 repairs since 1989, does the work, and a second jeweler checks the joint before the chain ships back under the 1-year workmanship guarantee.

Before you ship

  • Lay it straight or in a loose loop in a small sealed bag, never folded or knotted, so a snake chain doesn't pick up a new kink in transit.
  • Insure a gold chain at full value: for a $1,500 snake chain that's $35 (2.5% of the $1,400 above $100), both directions, on top of the $30 round trip. See how jewelry shipping insurance works.

Questions

Can a kinked snake chain be fixed?
Often it can be improved, but not always made invisible. Jewelers work the bent plates back, for example by drawing the chain through a hole in hard wood, which can make a kink much less noticeable. A kinked spot stays weaker, so cutting it out and rejoining the chain is sometimes the better repair. JewelryRepair.com starts kinks with the $19 Mail-In Evaluation, credited in full toward the work.
How much does it cost to fix a broken snake chain?
At JewelryRepair.com, one break is $43 in sterling silver ($30 plus $13 for snake), $54 in 14K yellow gold and $62 in 18K yellow gold. A second break adds $17. Each price includes a clean and polish and the 1-year workmanship guarantee, and shipping is $30 round trip per order. The repair page shows the exact total before you pay.
Why do snake chains kink so easily?
Because a snake chain is a tube of tightly nested plates with no open links to absorb a sharp bend. Fold it, wrap it around a finger, sleep in it or let a pendant pull it into an angle, and the plates are forced out of position and stay there. Store it laid flat or hanging, and fasten the clasp without folding the chain back on itself.
Can a box chain be repaired where it broke?
Yes, usually right at the break. The opened link is aligned and soldered closed with solder matched to the chain, then polished flush; a torn link is cut out or replaced with a matching one. At JewelryRepair.com that's $30 in sterling silver and $41 in 14K yellow gold, with no style charge for box chain. A hollow chain is laser-welded for $20 more.