Jewelry repair questions · Earrings & pendants

Earring backs for sleeping: which are comfortable and secure enough to sleep in?

Low, smooth backs that can't slide off: flat-back studs, whose front screws or presses into a post with a flat disc behind the lobe; screw backs; and small huggies with a firm hinge. Skip big butterfly backs, long posts, tall prongs and dangles, and check posts and stones often. Screwback conversion starts at $70 in sterling silver.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

$70screwback conversion, sterling silver ($40 + $30)
$30new posts, sterling silver pair
$40new posts, 14K yellow gold pair ($30 + $6 + $4)
50,000+repairs since 1989

The short version

  • Best for sleeping: flat-back studs, where a flat disc sits behind the lobe on a threaded or press-fit post; screw backs on a threaded post; and small, snug huggies whose hinge snaps firmly shut.
  • Worst: large butterfly backs, long posts, lever and omega backs, dangles, big hoops and tall prong-set studs.
  • What a pillow does: it presses the back into the lobe and drags the earring each time you turn over, which loosens friction backs, bends posts and works stones loose.
  • Check them often if you sleep in them. A back that slides, a post that leans or a stone that ticks when you tap it are all early warnings.
  • We're jewelers, not doctors. Whether to sleep in earrings at all, especially in a new piercing, is a question for your piercer or doctor. This page is about the hardware.

Prices

Service PriceWhat's included
Earring Back Conversion from $70 sterling, screwback
$136 14K yellow gold, screwback
The old fitting removed at its mounting point, the surface dressed back to bare metal, and a screwback fitting soldered on in your metal, so the back has to be unscrewed rather than pushed off. The earring itself is left untouched.
Earring Post Repair from $30For a post bent by months of pillow pressure: the old post removed flush, the pad cleaned to bare metal, and a new post soldered or laser-welded on straight, never glued. One earring is $10 less.
Stone Tightening from $50Stones that tick or tilt after overnight wear, secured under 10x magnification: prongs re-seated over the stone or a bezel burnished tight. Up to eight stones per order.
Prong Re-Tipping from $29Prong tips worn flat or lifted by snagging, rebuilt with new metal laser-welded on and shaped back over the stone. One to four prongs in sterling silver.
Hinge Repair from $45For a huggie or hinged hoop that springs open: a worn pin replaced, crushed knuckles trued, or a torn hinge tube re-soldered.

What a night in earrings does to the hardware

Lying on your side puts the earring between your head and the pillow. The back is pressed toward the lobe, the front is pushed into the pillow, and every time you turn, fabric drags across both. Three kinds of wear follow.

  • Friction backs loosen. Most studs are held by what Wikipedia's earring entry calls a removable friction back or clutch, also known as a butterfly or scroll back: two curled tabs that pinch the post. Pushed and pulled through the night, the tabs spread and the back creeps toward the tip of the post until a turn of the head slides it off.
  • Posts bend. Wikipedia's entry on body jewelry sizes points out that traditional earrings use only thin wire for support. That thin wire takes leverage at its base every time the earring is pushed into a pillow. Jewelers Mutual warns that bent or broken posts make backs less reliable and more likely to slip out of your ear.
  • Settings take knocks. Raised prong tips catch on pillowcases and hair, and a snag that lifts a prong even slightly can let a stone turn. A stone that has started to tilt is the sign to stop sleeping in that pair until it is checked.

Hinged hardware suffers too. Lever backs, omega backs and huggie hinges are small mechanisms, and lying on them loads the pin they pivot around from the side, night after night.

Earring backs for sleeping, compared

  • Flat backs (labret style). A flat disc sits against the back of the lobe, and the decorative front either screws into the post or pushes in on a pin. The Association of Professional Piercers describes both kinds: internally threaded jewelry keeps the threads on the removable end, so the part that passes through the skin stays smooth, and threadless, or press-fit, jewelry uses a pin coupling with no threads at all. The disc lies flat against a pillow and there's no clutch to slide off. The catch is that the post is a different design, so a regular stud can't simply take a flat back; the post has to be replaced. See can earrings be converted to flat backs?
  • Screw backs. The back turns onto a threaded post and has to be unscrewed to come off, which is why some more expensive studs have threaded posts. Pillow friction can't push it off. Keep the threads clean so the back seats fully, and avoid a post so long that its tip pokes out behind the nut.
  • Disc or padded friction backs. A wide disc, often with a soft pad, spreads pressure over more of the lobe than a small butterfly. It's still a friction grip, so replace it as soon as it slides on easily.
  • Small huggies and sleeper hoops. They hug the lobe with nothing loose behind it, and Wikipedia notes that sleeper hoops were originally meant to be worn at night. The hinge or catch has to snap shut firmly; one that springs open is worn.
  • Locking backs, which clamp onto a standard post, are designed not to slide off. They tend to sit bulkier behind the lobe than a disc, so check how one feels against your lobe before you sleep in it. If a post is bent or worn, no back grips it well, and the post needs replacing first.
  • Not for sleeping: lever and omega backs, with hinged hardware behind the lobe; large butterfly backs; drops and dangles that twist and catch; big hoops; and tall prong-set studs whose prongs snag.

Signs your sleep-in studs need attention

  • The back slides on and off easily: the back is worn. Try a new one. If a new back also slides, the post is bent or its groove has worn smooth.
  • The earring points down or sideways: the post has bent at its base. That's an Earring Post Repair, not something to bend back by hand.
  • The stone ticks when you tap the earring, or sits crooked: it's loose. Stone Tightening secures it under 10x magnification.
  • A prong tip looks flat or raised, or catches on fabric: it needs re-tipping before the stone goes missing.
  • A huggie opens on its own: the hinge is worn, and that's a Hinge Repair.

What a jeweler can change, and what it costs

These are the live configurator prices on Nov 18, 2026 for the fixes sleep-worn studs need most. Each includes a clean and polish and the 1-year workmanship guarantee, and the configurator shows the exact total before checkout.

  • Switch studs to screw backs: Earring Back Conversion is $70 in sterling silver ($40 + $30 for a screwback), $136 in 14K yellow gold ($40 + $55 + $11 + $30) and $142 in 14K white gold ($40 + $61 + $11 + $30).
  • Replace bent posts: $30 a pair in sterling silver or $20 for one earring, and $40 a pair in 14K yellow gold ($30 + $6 + $4). If the bent post is already a threaded screwback post, replacing it is $45 a pair in sterling ($30 + $15) and $55 in 14K yellow gold ($30 + $6 + $4 + $15); switching friction-back studs to screw backs is the $70 conversion above.
  • Secure the stones: Stone Tightening starts at $50. Prong Re-Tipping starts at $29 for one to four prongs in sterling silver and is $57 in 14K white gold ($29 + $23 + $5).
  • Fix a huggie hinge: Hinge Repair is $45 in sterling silver and $62 in 14K yellow gold ($45 + $11 + $6).
  • Flat backs, shorter posts or a lower setting: these aren't listed fixed-price services, so they start with a look at the earrings. The Mail-In Evaluation is $19, credited in full, and redesigns go through Custom Work, which starts with a $10 estimate. Post length is covered in earring posts that are too long, short or thick.

Can I fix it myself?

Partly. Replacing a worn friction back, cleaning screw threads with a soft toothbrush and warm soapy water, and swapping in a disc back are all safe at home. Bending a post back is riskier: metal hardens each time it's bent, so a post that has been straightened once is more likely to snap the next time, and one bent at its base can break off flush with the earring. Glue is no answer to a sliding back: the post keeps bending under it, and a jeweler has to clean it all off before soldering. Don't press prongs down with pliers either; prongs are closed with setting tools under magnification, and a slip can chip the stone.

Before you ship

Send both earrings and every back you have, sealed in a small bag inside the box, so new posts and backs come back matched. Shipping is $30 round trip per order by UPS, however many pairs are in the box, with the prepaid label ready in your account and $100 of coverage each way. For diamond studs, add full-value coverage before checkout: 2.5% of the value above $100, one fee for both directions, so a $1,200 pair costs $27.50 to cover in full (2.5% of $1,100). Earrings sent to JewelryRepair.com are worked on by Sky Jewelry, family jewelers on Lenox Avenue since 1989, with over 50,000 repairs since 1989. Each pair is photographed on arrival at our New York studio, posts and stones included, then a bench jeweler does the work, a second jeweler checks it, and the pair is photographed again before it ships back.

Questions

Can you sleep with screw back earrings in?
Yes, and they're one of the better choices, because a screw back has to be unscrewed rather than pushed off, so turning on a pillow won't slide it loose. Keep the threads clean so the back seats fully, and make sure the post isn't so long that it pokes out behind the nut. Converting studs to screw backs at JewelryRepair.com is $70 in sterling silver or $136 in 14K yellow gold.
Are flat back earrings good for sleeping?
Yes, flat backs are among the most comfortable earrings to sleep in, because the flat disc lies against the back of the lobe, and the front either screws in or presses in on a pin, so there's no butterfly back to dig in or slide off. A regular stud can't just take a flat back, though; the post itself has to be replaced. At JewelryRepair.com that starts with a $19 Mail-In Evaluation, credited in full toward the work.
Is it bad to sleep in diamond stud earrings?
It isn't harmful to the diamonds themselves, but it does add wear to the posts and settings. Pillow pressure bends posts and loosens friction backs, and prong tips can catch on bedding and lift, letting the diamond shift. If you do sleep in them, use screw backs or another back that can't slide off, and check regularly that each stone is tight and each post is straight. Stone Tightening at JewelryRepair.com starts at $50.
Do silicone or rubber earring backs work for sleeping?
They can be comfortable, because the soft material cushions the lobe, but they're still friction backs: they hold by grip alone, loosen with use, and a pillow can work them off. Replace them as soon as they slide on easily. For a valuable stud you wear day and night, a screw back is more secure; converting sterling silver studs to screw backs starts at $70 at JewelryRepair.com.
Why do my earring backs fall off while I sleep?
Usually a friction back's tabs have spread from being pushed and pulled, or the post has bent or its groove has worn smooth, leaving the back nothing to grip. Push on a brand-new back: if it holds, the old back was worn; if it still slides, the post needs work. New posts at JewelryRepair.com are $30 a pair in sterling silver and $40 in 14K yellow gold.
Can you sleep in huggie earrings?
Small, snug huggies are among the easiest earrings to sleep in, since nothing sits loose behind the lobe. Their weak point is the hinge or catch, which takes sideways pressure every night; if a huggie starts opening on its own, the hinge is worn. Hinge Repair at JewelryRepair.com starts at $45 for earrings in sterling silver and is $62 in 14K yellow gold ($45 + $11 + $6).