Jewelry repair questions · Earrings & pendants

Why do earring backs keep coming loose, and what are the most secure locking earring backs?

Earring backs usually loosen because a friction back's curls have spread, or because the post is bent or has lost its notch. The most secure options are screw backs on a threaded post and hinged omega or lever closures; locking backs help only on a straight post they fit. Screwback conversion starts at $70 in sterling silver.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

$70screwback conversion, sterling silver ($40 + $30)
$136screwback conversion, 14K yellow gold ($40 + $55 + $11 + $30)
$30new posts, sterling pair
50,000+repairs since 1989

The short version

  • Why it loosens: a friction back's curled tabs spread a little every time it goes on and off; the post's notch wears flat; or the post is bent. Jewelers Mutual warns that bent or broken posts make backs less reliable and more likely to slip out.
  • The quick test: push a brand-new back onto the post. If it grips, the old back was worn out. If it still slides, the post needs work.
  • Most secure: screw backs for studs you can't lose, lever backs for drops; details below.
  • Never glue a back or a post in place.

Prices

Service PriceWhat's included
Earring Back Conversion from $70 sterling, screwback
$136 14K yellow gold, screwback
Changes the fitting while leaving the earring untouched: the old post removed at its mounting point, the surface dressed back to bare metal, and a screwback, leverback or omega fitting soldered on in your metal. The jeweler reviews the intake photos and recommends a change before working if another fitting would serve the earrings better.
Earring Post Repair from $30For a bent post, a worn notch, stripped threads or a hinge-worn leverback: the broken hardware removed flush, the pad cleaned to bare metal, and new hardware soldered or laser-welded on straight, never glued. One earring is $10 less.
Hinge Repair from $45For a hinged hoop or huggie that pops open: a worn or bent pin replaced, crushed or misaligned knuckles trued or rebuilt, and a hinge tube that has torn away re-soldered.

The details: why earring backs work loose

Most studs are held by a friction back, also called a clutch, butterfly or scroll back: two curled tabs that pinch a smooth post, often settling into a shallow notch near the tip. All of the grip comes from spring tension. Each time the back is pushed on and pulled off, the tabs open slightly, until a scarf, a hairbrush or a pillow is enough to slide it off. The post wears too. Its notch flattens, and gold and silver are soft enough that a post bends when it catches on clothing or when you sleep on it, which leaves even a new back with nothing to grip.

Fit matters more than people expect. Posts aren't one size: they are usually 20 gauge (about 0.8mm) or 18 gauge (about 1.0mm), and a back made for one may grip the other poorly, which is why a replacement back from another pair can feel loose from day one. Screw backs fail differently: threads strip if a back is started at an angle, and grime in the grooves can make a back bind before it's tight.

The most secure earring backs, including locking and safety backs

  • Screw backs. A threaded nut turns onto a threaded post, so it has to be unscrewed rather than pulled off; that's why high-value studs such as diamond solitaires often have threaded posts. Trade-offs: slower to put on, threads can cross if a back starts crooked, and a smooth post can't take a screw back without being replaced.
  • Omega backs. A hinged loop swings down against the back of the lobe, with the post passing through it. Nothing can fall off, and the loop braces larger studs. Trade-offs: bulkier, and a worn hinge loosens the clamp.
  • Lever backs. A curved ear wire with a hinged lever that snaps shut behind the lobe; very secure for drops and dangles. A lever that no longer snaps shut is a hardware repair, not a reason to retire the earrings.
  • Locking backs (also sold as safety backs or earring locks). Add-on backs for a standard smooth post that must be released on purpose instead of sliding off. A sensible upgrade for a valuable stud, but only as good as the post: they need a straight post of the thickness they're made for, and they can't fix a bent post or a worn notch.
  • Friction backs. The least secure, and fine for everyday studs if you replace them as soon as they loosen; for heavy earrings see earring backs for heavy, drooping earrings.

In our jewelers' view, for diamond studs and anything you'd hate to lose, screw backs come first, then omega backs, then locking backs on a post in good condition. Hinged hoops and huggies are their own case: when they pop open, the hinge or catch is worn. Open French hooks are covered in how to keep fish hook earrings from falling out.

How to tell what's actually wrong

  • A new back grips, the old one doesn't: the back is worn. Replace it.
  • A new back still slides: look at the post under your phone's zoom. A bend, a flattened notch or a wobble at the base means an Earring Post Repair.
  • A screw back spins or stops halfway: clean the threads with a soft toothbrush and warm soapy water first, then swap backs between the two earrings. If the good back also spins on the suspect post, the post's threads are worn; more in replacing a lost or stripped screw back.
  • A lever back won't snap shut, or an omega loop is loose: the hinged hardware is worn and gets replaced under Earring Post Repair.
  • A hinged hoop or huggie opens by itself: that's a Hinge Repair.
  • The back works, but you don't trust it on a valuable pair: change the system with an Earring Back Conversion.

Can I fix it myself?

Some of it. Swapping in new friction backs, cleaning screw threads and pinching a butterfly back's curls closer are all safe at home. Bending a post back is riskier. Metal hardens each time it is bent and straightened, and past a point it fractures rather than bends, so a post that has been straightened before, or is bent at its base, is likely to snap on the next try. Don't use pliers on a post or a hinge, and don't glue anything: glue holds a post by a tiny surface while it's pushed, pulled and twisted with every wear.

What it costs at JewelryRepair.com

Prices from the live repair pages, Nov 18, 2026; each includes a clean and polish and the 1-year workmanship guarantee, and the configurator shows the exact total before checkout.

  • Earring Back Conversion (new fittings, earring untouched): in sterling silver, screwback $70 ($40 + $30), leverback $80 ($40 + $40), omega $100 ($40 + $60). In 14K yellow gold, screwback $136 ($40 + $55 gold + $11 for 14K + $30); in 14K white or rose gold, $142 ($40 + $61 + $11 + $30); in platinum, $238 ($40 + $168 + $30).
  • Earring Post Repair (replacing what's there): $30 a pair for sterling stick posts, $20 for one earring. In 14K yellow gold, stick posts are $40 ($30 + $6 + $4), screwback posts $55 (+$15), leverbacks $70 (+$30) and omega $75 (+$35).
  • Hinge Repair: from $45 for earrings in sterling silver.

Not sure whether it's the back, the post or the hinge? The Mail-In Evaluation is $19, credited in full toward the repair.

Before you ship

Send both earrings and every back you have, even if only one is loose, so the new posts and backs come back matched; put them in a small sealed bag inside the box. For diamond studs, add full-value coverage before checkout: 2.5% of the value above $100, covering both directions, so a $2,500 pair costs $60 to cover in full (2.5% of $2,400), up to $10,000 per package. JewelryRepair.com, the mail-in service of Sky Jewelry in New York, has done over 50,000 repairs since 1989.

Questions

Are locking earring backs worth it?
For a valuable stud on a straight, standard post, yes: a locking or safety back has to be released on purpose, so it won't slide off the way a worn friction back does. It can't fix a bent post or a worn notch, though, and it has to suit your post's thickness. For security built into the earring itself, screwback conversion is $70 in sterling silver at JewelryRepair.com.
What are the best earring backs for diamond studs?
Screw backs on threaded posts are the traditional choice, because a nut that has to be unscrewed can't be brushed off. Omega backs are a good alternative on larger studs. Converting 14K yellow gold studs to screw backs is $136 at JewelryRepair.com ($40 + $55 gold + $11 for 14K + $30), and $142 in 14K white gold.
How do I tighten a loose butterfly earring back?
Pinch the two curled tabs slightly closer together with your fingers, then test it on the post. That restores some grip, but the metal has already spread and will loosen again, so a new back is the better fix. If a brand-new back also slides, the post is bent or its notch has worn smooth, and Earring Post Repair replaces posts from $30 a pair in sterling silver.
Why do my screw back earrings keep coming loose?
Usually the threads are worn, packed with soap and skin oil, or were crossed when a back went on at an angle. Clean them with a soft toothbrush and warm soapy water, then swap backs between the two earrings to see whether the back or the post is at fault. A new pair of threaded posts is $45 in sterling silver ($30 + $15) and $55 in 14K yellow gold.
Can push-back earrings be converted to screw backs?
In most cases, yes. A screw back needs a threaded post, so the conversion replaces the smooth post with a screwback fitting and leaves the earring itself untouched. The jeweler reviews the intake photos first and recommends a different fitting if it would serve the earrings better. Earring Back Conversion to screwbacks is $70 in sterling silver; if you're unsure about a piece, the $19 Mail-In Evaluation is credited in full.