Jewelry repair questions · Earrings & pendants

How do I keep fish hook earrings from falling out?

Use small plastic or silicone earring backs, often called stoppers, on the end of each hook, and make sure the hooks haven't been bent open or worn thin. For a pair you can't afford to lose, convert the hooks to leverbacks, which lock behind the lobe: at JewelryRepair.com that's $80 in sterling silver or $146 in 14K yellow gold.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

$80leverback conversion, sterling silver ($40 + $40)
$146leverback conversion, 14K yellow gold ($40 + $55 + $11 + $40)
$50new French wires, sterling pair ($30 + $20)
50,000+repairs since 1989

The short version

  • Why they fall out: a fish hook, also called a French wire, has no closure. It stays in the piercing only because of its curve and the earring's weight, so anything that lifts the earring can lift the hook out.
  • Quickest fix: a small plastic or silicone stopper pushed onto the end of each wire. Cheap and effective, but it grips by friction alone and needs replacing as it stretches.
  • Check the hook itself: a hook that has been pulled open, flattened or worn thin sits loosely and slips out more easily, stopper or not.
  • Most secure: convert the hooks to leverbacks, which close behind the lobe with a hinged lever. There's nothing loose to lose.
  • Bent or snapped wires are replaced in your earring's metal, never glued.

Prices

Service PriceWhat's included
Earring Back Conversion from $80 sterling
$146 14K yellow gold
Replaces open fish hooks with leverback fittings in your earring's metal, so the wire locks behind the lobe. The earring itself is left untouched. Priced on the repair page by metal and karat before you pay.
Earring Post Repair from $50 sterling pairFor hooks that are bent, kinked, worn thin or snapped: the old wire removed, the joint cleaned to bare metal, and a new wire in your metal soldered or laser-welded on, never glued. One earring is $10 less.
Jump Ring Repair from $19When the drop is coming off the hook rather than the hook coming out of your ear: the small ring joining them soldered closed, or replaced with a heavier one.
Mail-In Evaluation $19For vintage or unusual fittings, or a pair where you can't tell how the hook is attached: examined under magnification, with photos and an itemized quote, credited in full toward the repair.

Why fish hook earrings slip out

A fish hook, or French wire, is an open curve of wire with no closure. Nothing locks it in. The front of the hook carries the earring, the tail hangs behind your lobe, and gravity keeps the curve seated in the piercing. As long as the earring hangs, it stays. Lift it, and the hook rides up with it.

That's why fish hooks go missing at predictable moments: pulling a sweater over your head, brushing or tying back your hair, taking a phone call, wrapping a scarf, lying on a pillow, or a child grabbing at a dangle. Each one pushes the earring up or forward until the tail clears the piercing, and the earring drops without a sound.

Four things make it more likely:

  • A hook that has opened. Gold and silver wire is soft. Each time a hook is forced through, snagged or stored in a tangle, the curve opens a little and the tail flares away from the front, so the hook sits more loosely in your ear.
  • A short or flattened tail. The less wire hangs behind the lobe, the less it takes to lift it clear.
  • Thin or soft wire. On Ganoksin's Orchid forum for jewelers, one maker gives 21 gauge as the industry standard for factory-made French hooks and notes that hooks in silver and gold are often flattened slightly to make them stronger. Thinner or softer wire bends open more easily.
  • A heavy, swinging drop. A heavy drop tugs the hook forward every time you move, working the tail toward the piercing.

Every fix, from quickest to most secure

  • 1. Earring stoppers. Small plastic or silicone retainers, often sold as fish hook earring backs, push onto the end of the wire behind the lobe. Wikipedia notes that small plastic or silicone retainers are sometimes used on the ends of ear wires. They stop the tail sliding back through the piercing when the earring is lifted. Choose ones made for thin ear wires rather than posts, slide them up close to the lobe without pinching, and replace them as soon as they slide: soft plastic and silicone stretch with wear, and a loose stopper gives no warning. Keep spares, because they're small and easy to drop.
  • 2. Restore the hook's shape. If a hook has opened slightly, ease the tail back toward the front with your fingers so the curve sits snugly again. Do it once and gently. Metal stiffens each time it's bent, a process called work hardening, and wire that has been bent back and forth eventually cracks at the bend.
  • 3. Replace worn, bent or thin wires. A hook that won't hold its shape, has a kink, or has worn thin where it rests in your ear is past reshaping. New wires in your earring's metal are soldered or laser-welded on; see replacing a broken earring hook.
  • 4. Convert to leverbacks. A leverback is a curved ear wire with a hinged lever that snaps shut over the tip of the wire behind the lobe, so the wire and lever form a closed loop through your ear. It can't slide out the way an open hook can, and there's no separate back to drop. This is the permanent fix for a pair you wear often or would hate to lose.

You'll also see kidney wires on ready-made earrings, a closed ear wire whose end clips into a catch. They aren't a listed choice on our conversion page, so leverbacks are the closed fitting we price here; for anything else, ask for a free quote first.

Stoppers or leverbacks? How to choose

  • Stoppers are enough for light, inexpensive drops you wear now and then, as long as the hooks still hold their shape.
  • Convert to leverbacks for gold, platinum, heirlooms and anything with diamonds, gemstones or pearls; for a pair you wear every day; and for a pair that has already lost one earring once.
  • Heavy drops pull on an open hook every time you move. A closed leverback can't be pulled out that way, though a heavy post earring that tips forward needs a different fix; see earring backs for heavy, drooping earrings.
  • For sleeping, sports and carrying small children, take hooks out. Wikipedia notes that tearing of the earlobe can be avoided by not wearing earrings during activities likely to snag them, such as sports. More in earring backs for sleeping.
  • Sensitive ears: a stopper doesn't change what touches your piercing; the wire does. New wires and leverbacks are made in your earring's own metal, which the repair page asks for.

How a jeweler converts fish hooks to leverbacks

At JewelryRepair.com, your earrings are photographed when they arrive at our New York studio, before anything else, and a jeweler examines both under magnification. If the work needed differs from what you ordered, you approve the change before anything is done.

  • The old hook comes off where it joins the earring, and the surface is cleaned back to bare metal. The earring itself stays as it is.
  • A leverback fitting in your earring's metal goes on so the drop hangs at the angle it was designed to, soldered or laser-welded in place. Laser welding is the tool of choice when pearls, opals or other heat-sensitive material sit close to the joint, because it puts heat only where the joint is.
  • Heat stays off the mechanism. Stuller, a jewelry findings supplier, warns that torch work on a spring-loaded finding risks annealing (softening) the spring and ruining it, and advises removing the hinge pin and lever before soldering, or protecting them with heat-sink paste.
  • Finish and check. The pair is cleaned and polished, a second jeweler checks the work, and the earrings are photographed again before they ship back with a card naming the jeweler.

Can I do it myself?

Partly. Stoppers are a home fix, and so is easing a slightly opened hook back into shape once, by hand. Beyond that, go carefully:

  • Don't squeeze the curve tight with pliers. A hook closed too far won't pass comfortably through the piercing, and pliers mark soft gold and silver.
  • Don't keep re-bending a hook. Each bend work-hardens the wire until it snaps, usually where it meets the earring.
  • Don't glue anything. Glue can't take the strain of an earring going in and out of your ear, and residue has to come off completely before a proper repair.
  • Swapping hooks yourself can work on inexpensive fashion earrings whose hooks hang from an open loop. If the hook is soldered to the earring, or the loop it hangs from is soldered closed, it's bench work: forcing it open with pliers usually leaves a weaker joint than the one you started with.

What it costs at JewelryRepair.com

These are the configurator totals on the repair pages as of Nov 18, 2026; the page shows your exact total before checkout, a clean and polish is included, and the work carries the 1-year workmanship guarantee.

  • Converting to leverbacks (Earring Back Conversion, priced by metal, karat and the new style as configured on the repair page): sterling silver $80 ($40 + $40); 10K yellow gold $135 ($40 + $55 + $40); 14K yellow gold $146 ($40 + $55 + $11 + $40); 14K white or rose gold $152 ($40 + $61 + $11 + $40); 18K yellow gold $168 ($40 + $55 + $33 + $40); platinum $248 ($40 + $168 + $40).
  • New French wires (Earring Post Repair, current post style Wire, priced per pair): sterling silver $50 ($30 + $20), or $40 for one earring; 14K yellow gold $60 ($30 + $6 + $4 + $20); 14K white or rose gold $65 ($30 + $11 + $4 + $20).
  • A drop coming off its hook: Jump Ring Repair, from $19 in silver.
  • Gold-plated or fashion pairs: Earring Post Repair lists gold-plated at +$16, but plated pieces that need solder work start with a free quote, so you see the price before anything ships.
  • Not sure what's wrong: the Mail-In Evaluation, $19, credited in full toward the repair.

Rush Service ($50) ships an eligible repair back 2 to 3 days sooner. Compare other earring jobs in how much earring repair costs.

Before you ship

  • Send both earrings, even if only one hook slips, so the new fittings come back matched. Put the pair, and any stoppers you use, in a small sealed bag.
  • Name any pearls, opals or other delicate material in your order note, so the jeweler plans the joint around them.
  • Pack the bag in any sturdy small box, padded so nothing shifts, with nothing on the outside naming the contents, and drop it at any UPS location with the prepaid label from your account.
  • Shipping is $30 round trip per order, however many pairs are in the box, with $100 of coverage each way. For gold or diamond drops worth more, you can insure the full value up to $10,000, both ways, for 2.5% of everything above the first $100: earrings valued at $1,500 cost $35 to cover ($1,400 × 2.5%).

Sky Jewelry, the family jewelers on Lenox Avenue since 1989, runs JewelryRepair.com as its mail-in service and has completed over 50,000 repairs. A bench jeweler at the New York studio does the work, a second jeweler checks it, and your earrings come back in a plain box, signed for at your door.

Questions

What are the best earring backs for fish hook earrings?
Small plastic or silicone stoppers made for ear wires are the usual choice: they push onto the end of the hook and stop it sliding back through the piercing. They grip by friction alone, so replace them as soon as they loosen. For a pair you can't risk losing, a leverback conversion is more secure; at JewelryRepair.com it's $80 in sterling silver and $146 in 14K yellow gold.
Can fish hook earrings be changed to leverbacks?
Yes. An Earring Back Conversion replaces the open hooks with leverback fittings in your earring's metal and leaves the earring itself untouched. At JewelryRepair.com it's $80 in sterling silver ($40 + $40), $146 in 14K yellow gold and $248 in platinum, priced on the repair page before you pay. Send both earrings so the new fittings match.
Can I put a regular butterfly back on a fish hook earring?
Not reliably. Butterfly and other friction backs are made to grip a straight post, and Stuller, a findings supplier, puts common post standards between 20 and 16 gauge, while factory French hooks are often 21 gauge, thinner still, and curved. A back made for posts tends to slide along a hook. Use a stopper made for ear wires, or convert the pair to leverbacks.
Why do my fish hook earrings keep falling out?
Because nothing holds them in: a French hook has no closure and stays put only by its curve and the earring's weight, so a sweater, a hairbrush or a pillow can lift it out. A hook that has opened, has a short tail or is made of thin, soft wire slips out more easily. Add stoppers, reshape or replace the hooks, or convert to leverbacks, from $80 in sterling silver.
Is it safe to sleep in fish hook earrings?
It's better not to. Lying on an open hook can push it out of the piercing or bend the wire open, and a hook that catches on bedding pulls on your lobe and can drop the earring somewhere you won't find it. If you want to keep earrings in overnight, small studs or a closed fitting such as a leverback are the safer choice; see earring backs for sleeping.