Jewelry repair questions · Chains, clasps & bracelets

How do you remove a permanent bracelet, and can it go back on?

Cut it at the jump ring, the small ring that was welded shut to close the chain, with small sharp scissors, nail clippers or wire cutters. Cut there and keep the chain, and a permanent-jewelry artist can usually weld it back on with a new ring. To make it removable instead, JewelryRepair.com can fit a clasp, from $48.

From JewelryRepair.com: over 50,000 repairs since 1989 · 4.9 from 187 Google reviews (as of )

$48Clasp Replacement: a small spring ring or lobster in sterling silver
$67a small 14K yellow gold lobster clasp fitted ($48 + $19)
$30round-trip UPS shipping per order, prepaid label in your account
50,000+repairs since 1989 by the family behind Sky Jewelry

The short version

  • Cut the jump ring, not the chain. It's the small ring welded shut where the two ends meet. Cut there and the chain stays whole.
  • Tools: small sharp scissors, nail clippers or small wire cutters. No pulling.
  • Keep everything, chain, cut ring and any charm, in a small bag.
  • It can usually go back on: a permanent-jewelry artist welds a new jump ring, with your wrist there.
  • Or make it removable with Clasp Replacement, from $48 at JewelryRepair.com.
  • For an MRI, plan to take it off, and follow your imaging center's instructions.

Prices

Service PriceWhat's included
Clasp Replacement from $48Turns a welded bracelet into one you can take off: a spring ring, lobster or box clasp sized to the chain, soldered on and action-tested. A small spring ring or lobster in silver is $48; a small 14K yellow gold lobster $67 ($48 + $19); a small 14K white gold lobster $69 ($48 + $21); a small 14K yellow gold spring ring $76 ($48 + $28).
Jump Ring Repair from $19A jump ring soldered closed or replaced with a heavier one: $19 in silver, $31 in 14K yellow gold ($19 + $7 + $5). If a chain that never had a clasp needs an end ring for the clasp to hook into, the jeweler confirms it on arrival and you approve the cost first.
Chain Soldering from $30Only for a chain broken in two or more places, so a loose section can be rejoined before a clasp goes on: $30 in silver, $41 in 14K yellow gold ($30 + $7 + $4). A single cut doesn't need it; the clasp goes on at the cut.
Chain Shortening from $44If the bracelet sits too loose once a clasp adds its length: links come out at the clasp end and the clasp is re-soldered, and the removed links come back to you. $44 in silver or 10K yellow gold, $50 in 14K yellow gold ($44 + $6).
Mail-In Evaluation $19For gold-filled or plated chains, or anything you're unsure about: an itemized quote with photos, credited in full toward approved work.

Why the jump ring is the place to cut

A permanent bracelet is a length of chain fitted to your wrist with no clasp. Jewelers Mutual, the jewelry insurer, describes how it's closed: a micro-welder joins the two ends, with a small leather or metal barrier between chain and skin. Because there's no clasp, it notes, the welded link becomes the strongest part of the chain.

Cutting that ring is still the cleanest way off. Jewelers Mutual says it's best to cut at the original weld site, and guidance from Sunstone, a maker of permanent-jewelry welders, quotes an artist: if the jump ring is cut, the bracelet or anklet can be put back on. Cut through a chain link instead and that link is damaged, so a snug bracelet may come back a link shorter.

The jump ring sits where the two ends meet and often looks a little different from the chain's links: rounder, or a slightly different size. The same guidance suggests artists point it out before you leave.

Cutting it cleanly and safely

  • Small, sharp scissors cut a fine permanent chain, as both Jewelers Mutual and the welder maker's guidance suggest; the welder guidance adds nail clippers. Small flush wire cutters give the cleanest cut on a heavier chain.
  • Lift the jump ring away from your skin with a fingernail or a thin card before you cut.
  • Work over a towel or tray, so nothing drops into a drain or carpet.
  • One clean cut through the jump ring only. Don't twist the cut ring open or pull on the chain; that stretches the end links the next jeweler works on.
  • Don't yank it off. Jewelers Mutual notes dainty permanent chains are designed to break under extreme pressure to prevent injury, but a tug breaks the chain at a random link and stretches the links around it.

Taking it off for an MRI, surgery or other procedures

RadiologyInfo.org, the patient site of the American College of Radiology and the Radiological Society of North America, tells patients to remove all metallic belongings before an MRI, including jewelry: the magnet can pull on metal, metallic items can heat up, and jewelry near the scanned area can interfere with image quality. The welder maker's guidance adds that metal can distort X-ray, CT and MRI images.

  • Your imaging center or hospital comes first, whatever the metal.
  • Cut it yourself beforehand, at the jump ring, so you choose where it's cut and keep every piece.
  • If something can't come off, tell the MRI technologist, as RadiologyInfo stresses, so staff can take precautions.

Afterward: back on, or removable for good

  • Re-welded on your wrist. Cut at the jump ring and kept, the chain can take a new welded ring; Jewelers Mutual notes many jewelers re-weld a saved chain for a small fee. It needs your wrist there, so JewelryRepair.com doesn't do it by mail.
  • Fitted with a clasp. Clasp Replacement fits a spring ring, lobster or box clasp sized to the chain's gauge, soldered on rather than pinched closed, then action-tested. A clasp can open or wear where the weld couldn't, and it adds a little length; if links need to come out, the jeweler confirms it on arrival (Chain Shortening from $44). If a chain that never had a clasp needs an end ring, that's Jump Ring Repair, from $19, approved by you first. Weighing the clasp against a re-weld is covered in can a broken permanent bracelet be rewelded?
  • Cut through a link? A single cut still leaves one strand with two ends, so it only needs the clasp; the jeweler confirms on arrival whether the damaged link should come off at the clasp end.
  • Broken in two or more places? The loose section is rejoined with Chain Soldering first: $30 in silver, $41 in 14K yellow gold.

What it's made of decides the next step

  • Solid 14K gold. Jewelers Mutual says most professionals use 14K gold for permanent jewelry. Clasp Replacement lists 14K yellow and white gold clasps: a small lobster is $67 in yellow ($48 + $19) or $69 in white ($48 + $21).
  • Sterling silver: $48 for a small spring ring or lobster.
  • Gold-filled. Rio Grande, the jewelry supply house, describes 14/20 gold-filled as 14-karat gold bonded to a base-metal core, the gold being 1/20 of the weight. It isn't listed on Clasp Replacement, so start with a free quote through the contact page or the $19 Mail-In Evaluation.
  • Plated. The welder guidance tells artists to avoid plated metals for lack of durability. Chain Soldering lists gold-plated chains (+$17); for a clasp on a plated chain, ask for a quote first.
  • Not sure? Choose Not sure for the metal in the Start a Repair wizard and it's tested at no charge.

Sending it to JewelryRepair.com

Seal the chain, the cut ring and any charm in one small bag, and put your wrist measurement and how snug it was in the order notes so the clasp ends at the right length. There's no minimum order: one clasp can be booked alone. Shipping is $30 round trip by UPS, with the prepaid label waiting in your account; $100 of coverage is included each way, and covering a $600 gold bracelet in full adds $12.50 (2.5% of $500). The rest is on the shipping and insurance page.

The bracelet is photographed when it reaches the New York studio and again before it ships back. A bench jeweler does the work, a second jeweler checks it, and it carries the 1-year workmanship guarantee. JewelryRepair.com is run by Sky Jewelry, family jewelers on Lenox Avenue since 1989, with over 50,000 repairs since 1989.

Questions

Can I remove a permanent bracelet myself?
Yes. Snip the jump ring, the small ring welded shut where the chain's ends meet, with small sharp scissors, nail clippers or wire cutters, then slide the chain off. Jewelers Mutual advises cutting at the original weld site rather than through the chain, which keeps the bracelet whole so it can be welded back on. Keep the chain and cut ring together.
Do you have to take off a permanent bracelet for an MRI?
Usually, yes. RadiologyInfo.org tells patients to remove all metallic belongings, including jewelry, before an MRI, partly because metal near the scanned area can interfere with the images. Follow your imaging center's instructions, and if something can't come off, tell the technologist. Cutting it at the jump ring beforehand means it can go back on afterward.
How do I take off a permanent anklet or necklace?
The same way as a bracelet: find the welded jump ring where the two ends meet and make one clean cut through it. Sunstone's guidance quotes an artist saying a bracelet or anklet cut at the jump ring can be put back on. On a necklace, have someone else make the cut so the blade stays away from your skin, and keep every piece.
Can I make a permanent bracelet removable?
Yes, by having a clasp soldered on. At JewelryRepair.com, Clasp Replacement is $48 for a small silver clasp and $67 for a small 14K yellow gold lobster ($48 + $19), action-tested before it ships back. A clasp adds a little length, so note your wrist size. Whether a clasp or a re-weld suits you better is weighed in can a broken permanent bracelet be rewelded.
What if I cut the chain instead of the jump ring?
It's still fixable. A single cut leaves one strand with two ends, so an artist can weld a new jump ring there, or a jeweler can fit a clasp at the cut, from $48 in silver at JewelryRepair.com. The cut link is damaged, so the bracelet may end up a link shorter; the jeweler confirms on arrival whether it should come off.